Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Hi All,
SDK => v17.1.0
IDE => Segger
Project => ble_app_bps
I use LightBlue to connect my board,and going down to the device information service I choose system...
Hi,
I'm using nRF5340 DK, one board is programmed as central and 2 boards are programmed as peripherals. When I flash the central program it is selecting a random board...
Hello,
we are currently experiencing issues with the SPI interface which we suspect is due to the behaviour of the MOSI line in idle state. We have noticed that during communication...
Hello,
I am planning to test ethernet module on nRF9160, use SEGGER SDK v1.7.0 for compile the programs. In Q&A I saw using can bus module & ENC424J600 ethernet controller...
Hey,
I try to read the CRC from E-Paper display series 1.02 inch (GDEW0102L4f) with no success (I'm working with nRF52833 Development Kit)
My code and the official Goodisplay...
Hi
I can‘t find the bank size configuration in the project secure_bootloader_uart_mbr_pca10056。 For safety reasons, I want to artificially divide the size of bank0 and bank1...
Sir,
I am using a U-BLOX NINA B302 (nrf52840) connected to a SEGGER J-LINK to program it!
Using the J-LINK flash i can program the NINA B302
But, on VISUAL STUDIO +...
Hello!
I am having 3 nrf5340 devices; 2 Gateways and 1 Headset. I am trying to achieve the scenario where I can allow the Headset connects to selectively one of the 2 Gateways...
I recently got the nrf52840dk board and I am trying to use it with the Nuttx embedded OS. However, I am having some issues flashing the nuttx binary on my board.
this is...
I'm trying to accurately measure our 3.0 volt coin battery (CR2450).
Our product consume low power (<50 uA) and we measure the battery voltage every minute.
We must...
Hello,
I've been trying to get through SUPL client library license signup process but I my request get denied every time.
I think I've done everything that is required...
I wrote a firmware on my dk52 and am advertising some data to the nRF Connect for Mobile App.
Is there any way on how I can copy or send the received data (service data...
Hi,
I have the following ouput using the throughput example:
Altered output format a bit to give me the same for local and peer.
But I was wondering why there is a...
Hi All,
I am running nrfConnect SDK v1.8.0 ad started a new sample LBS project. I ultimately want to have 3 devices, 1 being a Central and 2 Peripherals both running LBS...
Hi
Nordic Team
I used nRF5_SDK_17.1.0. I have a very difficult problem:
I now only want to configure an RX pin and no TX pin. Can the serial port receive data function...
