Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Currently I have implemented Central using nrf52810, SDK 14.2 / Softdevice S132.
I want to know how to do OTA upgrade in Central.
Or I would like to get an example currently...
What's the proper way to turn off BLE to conserve power?
I have a board with DC power input and battery backup. When the DC power fails, I want to finish what I'm doing...
I have an nRF 52832 running the SDK 15.2. I have a few general questions because I'm seeing behavior I don't understand and doesn't seem to be right.
If I erase all the...
I am attempting to load up the default NRF project "AT_Client" located at ...\ncs\v1.4.2\nrf\samples\nrf9160\at_client project, however, whenever I attempt to load it with...
Hello
I studying the nrf9160 , is it better to use the UART interface versus the SPI and do I need to use the flow control ?
Thanks a lot
Stephane Boudaud
Hi,
We developped a custom NRF9160 board and it works fine, it connects to LTE-M. We then designed a new version of the same board by adding few things (like NRF52833 MCU...
The sample code at ncs/nrf/samples/nrf9160/mqtt_simple is not connecting. I dod not make any changes to the ode. I am using NB-IoT. LTE is connected. The link monitor, LTE...
I just spent hours trying to use TTM with nRF52840 and I wanted to share the fix:
You need to use the Thread FTD CLI (USB) pre-compiled binary from v4.0.0 of nRF SDK for...
I would like to clarify my understanding of the connection interval since it doesn't seem to match what I'm seeing in the nrf connect mobile app.
Currently I've set my...
Hello all!
I have been modifying the door_lock_nus example to add the set pin command (0x05 from zcl reference). So I have modified the zigbee callback to read the new...
Hi,
I am wondering how to let these both run together. If I understand the sdk_config correctly the app_scheduler event queue can be used for the USB directly. But how should...
When performing a DFU the 2nd stage increments the expected device BLE address by 1 when the device being updated reboots. This potentially conflicts with the address of an...
We have developed a PCB using nrf52840 controller. It's a brand new controller. I am using SEGGER embedded studio for programing.
I have flashed an example code ble_app_blinky_pca10056_s140...
