Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
I am trying to port my working application from a nrf52811/s112 to nrf52832/s132, both with SDK 16.0.0. I'm at the end at the process, it builds fine on nrf52932, I just can...
I'm new to develop firmware on nRF9160-DK, and my first target to add APN to use LTE-M.
For now, I'd like to do a simple way in the below even this is temporary.
=> Hard...
Hello,
I try to transfer the thread_mqtt_sn_client_publisher example from the pca10056 to the pca10059.
Before that, I tried out the example with the pca10056, a boarder...
Hello! me and a coworker are developing a library for communicating with a peripheral via UART. The main idea is that when we send a command, we should get the corresponding...
Hello Team,
I am new to the OTA process for nRF52840. Please help me with the below query.
1) Is it possible to perform the OTA over BLE and over thread network as well...
Hi, We use the QSPI already very well for a flash device that has the correct commands. Now we want to use a SRAM, also QSPI prepared, but it has some other commands, there...
I'm trying to decide on a protocol to use between two nRF52840s.
Both will connect to an App and each other at the same time
Latency is important because the communication...
Hello everyone,
I'm currently trying to get a SiLabs WF200 WIFI module working with a nRF9160 as the host running on Zephyr. Unfortunately I do not get any clock signal...
Hi,
I am testing the advertisement packet scanner based from nRF5_SDK_17.0.2_d674dde\examples\ble_central\ble_app_uart_c.
At current stage, I can receive the advertisement...
I want to use bootloader for nRF52811.
On nRF5 SDK 17,
exmaples/dfu/secure_bootloader/pca10056e_s112_ble/config/sdk_config.h #define NRF_DFU_APP_DATA_AREA_SIZE 8192
...
I am writing a basic health device application, It starts, loads saved data, starts advertising, takes measurements, if a connection occurs the data is transferred, other...
I have compiled the example application ncs\v1.4.0\zephyr\samples\boards\nrf\system_off configured for the nRF52dk_nRF52832
This example consumes 450-500uA (SB9 cut)......
Hello Nordic support team,
We are making product relate to battery service.
Tool and SDK: - nRF5_SDK_17.0.2_d674dde
- SEGGER Embedded Studio for ARM Release 4.52c
...
Hi, I am doing some development in nrf52810. where i want to use BUZZER to produce TONES
I am using SDK17.0.2 SES
I want to create tones instead of just beep sound in...
