Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
I'm using SAADC like this:
And I'm not getting the done event. I've also tried not low power mode.
If I place a breakpoint in nrfx_saadc.c nrfx_saadc_irq_handler, after...
I'm compiling a custom application using the CMake scripts in the nRF mesh SDK , and I'm trying to print floats using vsnprintf (I'm guessing the problem is the same as with...
Hi,
We are using nRF52 DK tool to sniff BLE data. We we using Wireshark plugin to interface nRF52 DK tool. nRF52 is updated with latest firmware. We keep the tool in between...
Hi,
we are porting code of our project from SDK 14.2 to SDK 15.3.0, and have encountered unexpected behavior from the fstorage module. Even though SoftDevice and BLE stack...
I'm trying to work with the PC-BLE-Driver with the connectivity firmware. I've loaded the connectivty firmware and the application appears to connect to the board. But I'm...
Hi,
I working on the module developed based nRF52840.
I would like to clarify some doubts regarding the TX power of the chip.
The TX power value is higher at the temperatue...
I think there are should be smartphone cpu with bluetooth 5 long range mode support.
for example Qualcomm Snapdragon
Qualcomm Snapdragon 439
Qualcomm Snapdragon 710...
Hi all,
I am looking for some advice on how to implement a couple of extra characteristics(Related with battery) with the Battery Service apart from the usual Battery Level...
In " nRF51 Series Reference Manual ", in TWI chapter, it is mentioned to configure the GPIO pins with drive strength S0D1, to secure correct signal levels on the pins used...
In my application I'd like to use nRF52810 due different reasons. Since we're still in evaluating phase, without even choose a brand and related EVK, I've some basic questions...
Hi,
I am adding "install codes" function to my products.
Questions are
1. How many entries can i add with "zb_secur_ic_add" at ZC site?
2. Can i retrieve mac/ic (install...
Hi,
We are starting to measure the power of our nrf52840 based design.
I'd like to establish the power number for Idle() , since system will be in Idle() most of the time...
Hi,
I"m using SDK 15.3.0 with an NRF52840 dev board. I'm trying to record the timings from an incoming IR signal. In doing so I'm using LPCOMP with an analog input pin to...
I am trying to use the RF5 BLE CLI (Nordic NUS driver).
I need a plug and play COM port for Windows, iOS, and OS/X. This has to work for a customer.
It pairs easily, but...
My team is in the process of developing a product that uses the Fanstel BC832 module and have been running into issues trying to implement buttlonless DFU in our application...
