Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hi, I am new to Nordic devices. I have purchased Nordic Thingy91 (PCA20035).
I need a small clarification on the programming/flashing the nRF9160 and nRF52840 on Thnigy91...
Hello
I am trying to operate the ble_peripheral_hrs example found at SDK 5.11 (several years ago) for Segger, but I can't found a project (*.emproj) for it.
Have you know...
Hi,
I have nrf52840 on my custom board (Based on IMX6, Running Yocto linux) which is connected over UART.
I want to an OTA of zephyr OS on that chip over serial and for...
We have a custom device that we profile with a PowerProfiler (external DUT). Device is battery powered.
We have a strange idle current: cca 5 uA for 2 min, then 900 uA ...
Hello,
I am new to the nrf9160. i am quite confused in between nRF Thingy91(pca20035) and nRF9160DK (pca10090) .
What are the steps i need to follow to get start with...
Hello:
I want to change uart0 tx and rx pin from default 28 and 29 to 10 and 11.
I know the i2c pin change need to change nrf9160_pca10090ns.overlay in app.
So I tried...
For quite a while I've noticed that across multiple custom boards using the nRF52 I've been seeing low-level current spikes from a part that is in SYSTEM_OFF mode. They are...
i got 'LIS2DH12_ADDR' undeclared (first use in this function) error when i build my project but i already define it in pca20020.h file.
this image is i define about...
Hi,
I found the TRACE connector on nRF52833 and 52840 DK has its pin 9 connected to ground.
But in the datasheet of JLink/JTRACE, the TRACE connector has following pinout...
Hi,
Could you tell me where can I find some guide how to add DFU into NRF BLE examples, e.g. ble_app_proximity ? I would like to add DFU like a service into the app, not...
We are having a very difficult time soldering the nRF52840 to the PCB. Our Operations Department is asking what the lead finish of the BGA balls is. Would be great to get...
Hi,
I compiled and downloaded GPS sample, I got the following messages:
Tracking: 0 Using : 0 Unhealthy : 0
Seconds since last fix: 600
Scanning [ _ ]
Over 10 minutes...
Dear All,
I have noticed the following behaviour:
When the modem goes to PSM, it is not possible to retrieve the RSRP, using the CESQ or the XMONITOR AT commands. This...
Hi,
I am using NRF52840 DK in our project . I am using 15.3.0 SDK and soft device s140 in our project .Here the nrf52840 dk board is client and other controller bluetooth...
