Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I have code developed for the nRF52832 based on the Zephyr RTOS. If I switch to the nRF5340 with Zephyr RTOS, would it be possible to develop by simply uploading the additional...
Dear all:
I have built a project(ex: matter bulb) in Nordic SDK, the generated load is zephyr.hex which size is about 2345kb ;
Then I open nRF Connect Programmer, and...
I'm attempting to get our wearable remote to interact with a GoPro using their API and am getting the error in the subject line when attempting to start scanning. I've checked...
I am working on scanning and connecting to an iPhone device in NRF52840dk, but I am not able to receive my iPhone while scanning. If there are any different ways, please let...
Hello!
Looking for some guidance on how I should start debugging an issue I'm experiencing trying to get the Zephyr fdc2x1x sample code running on a custom PCB that uses...
Hi everyone,
I am working with the nRF SDK v2.0.4 for VsCode and with the nRF52840 DK.
I want to develop an application that transfer in real time the data collected...
I'm essentially building a BLE to UART gateway to allow our microcontroller device to talk to our apps. The BLE section is the nRF52840 and I'm trying to simply use it to...
I am trying to install the nrf connect SDK on my Macbook M3 Pro. But i am unable to do so. Neither VSCode extension nor the Toolchain manager works for me.
Clicking install...
I'm currently troubleshooting potential timing-related collisions associated with the NRF radio. I use a custom protocol on a single specified channel (no frequency hopping...
Hi, I have a custom board built around a nRF9161. When I test with the at_client only AT+CGSN=1, AT+CGMI, AT+CGMM and AT+CGMR return with the expected string. All other commands...
Hi all
I'm working on custom board build with an nrf9161. Right now I'd like to use a gpio as input with interrupt for i2c captor icm20948. So for I've searched and I think...
Hello.
I have 2 designs of PCB to make, I have their schematics almost complete. Both use the nRF52840.
My doubt is if for each PCB, if I will be able to use at the same...
Hi
Can you please supply me with the mechanical dimensions for the nrf52840 dk? I can not find anything. I would like to have the dimensions of the mounting holes in relation...
Hi,
Previously, I used the nRF52840 to work as a host. Similarly now, I hope to use the nRF52832 to work as a host, but it seems that this cannot be achieved simply by changing...
I have a custom board with a nrf52832 chip on it and I am currently trying to build my own application for it.
I have successfully managed to compile and flash it using...
