GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
I noticed on my custom PCB that pairing stopped working, and was getting "reason 0x13" as the disconnect. This disconnect reason I believe is from the phone disconnecting...
Hello everyone,
I’m working with an nRF52840-based board (XIAO form factor) and facing an issue related to USB enumeration and DFU mode detection during development.
Board...
Hi there,
I am considering using one of the npm1300 LDOs to supply 3.6V to the battery backup pin of a uBlox MAX-M10 module using a 100uF capacitor as energy storage for...
HI,
I am using an nRF52840 DK as a Bluetooth LE sniffer and have followed all the steps described in the official documentation .
In Wireshark, I can see “nRF Sniffer...
Hi Nordic team,
We have used shell example of Zigbee sample to connect to an end device. We want to extend the FEM feature of nrf54L05 for this example. We have already...
I want to implement dual-mode operation of LORAWAN and BLE, but when using the SoftDevice, the interrupt on the LORAWAN DIO1 pin does not trigger. I suspect it is being blocked...
Hi,
I have a question after using the DMIC example on the nRF5340:
how do I adjust the PDM clock frequency to 1.28MHz, or how can I achieve this by changing the value...
hello Nordic
i am working with nrf 52840 and 52832. using ncs v2.8.0
i am saving a coredump to flash partition and i am using gdb server - client to try to parse the coredump...
Hello,
I'm migrating an ANT+ BPWR application from **nRF5 SDK** to **NCS v2.5.1** but cannot install the sdk-ant module.
**Background:** - Previously used nRF5 SDK with...
Hello,
I send a ticket because I have an issue to access and write files to a SD Card with NRF54L15DK and 3.1.0 SDK and toolchain.
Can you help me please ?
Here is my...
Hello,
we are trying to run Gazell samples on the nRF54L15-DK, but the protocol & board combination doesn't seem to be supported by version 3.2 of the nrf Connect SDK...
We would like to synchronize several Nordic thingys 53. The Approach is to send two timestamps from a central to them (peripheral) via Bluetooth Low Energy with 100 ms delay...
Hi
I try to start with ST7789 display on nRF54L15 and there are bus fault after add LVGL library. The project is building correctly, but stop just after leave bootloader...
Hi,
I accidentally opened and subsequently programmed the PPK-II in Bluetooth Low Energy module startup. The programming didn't complete but resulted in an error. Now...
