Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
hello team,
I'm using nRF CONNECT 3.3.0, SEGGER Embedded studio IDE with Cmake version 3.16.5 and SDK
my device (nRF9160DK) is connected with system but SEGGER Embedded...
Hi, I've successfully passed nRF Connect SDK installation by using GSA application (macOS 10.15.3, python 3.7.7, west 0.6.3). Now I'm in the SES 4.52c and have a problem in...
It looks to me that in NCS/Zephyr it is only possible to configure the system clock to operate off of the LFCLK. I haven't been able to find any Kconfig options that would...
We have 2 identical development boards and have been using only one until now. I was able to download code into the 2nd board successfully but it will not run. It does not...
Hi,
what is the valid range of interval for NRF_SO_GNSS_FIX_INTERVAL? when we set it to 5 it will failed, but 1 and 10 can be successful.
here is the code and error log...
I have a nrf24 transmitter and receiver that I want to set up for max speed. I have my SPI's both at max and I set the crf24 register to reflect 18db (was not sure how this...
Hi,
I am setting up nRF connect SDK into Mac, however I received an error below when setting up a project in SEGGER:
Could you please help me to remove this error...
Hi,
I am currently trying to understand the BLE mesh concepts, but its a quite tough process. At the moment I am wondering the following:
Let's say that I wand to...
HI
How stable is the serial_uartesexample in nRF5? I'm running it on a PCA10056, the example works for about 5 seconds and then UART RX stops, i.e. nothing is received after...
I see unexpected delays when running MQTT sample. The issue seems to be network related. When connecting delay is "normal" but after a few seconds roundtrip delay increases...
Hi everyone：
My case is to reveice some useful information form beacon device, but I have no ideal that is the softdevice s112 support observing so far ？
The s132 softdevice...
Hello guys,
We are working on the project and using DK 9160. We want to use LTE Cat M1 connection, mqtt tls and we need full functionality embed tls. We started with demo...
I am having trouble with the DFU/bootloader. I have built a board using the nRF52832 chip which I can program using SES using JLink connection, using SDK 16 and s132. I now...
Hello,
I am trying to figure out how the button presses in the module esb_low_power_ptx_pca10040 are creating events?
I have done some research and do not see this module...
