Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
Hi
I am working on nRF52832 DK and using Ubuntu 16.04 and Segger Embedded Studio as IDE. When I try to build the AES_CTR program, the following error comes up.
Can anyone...
Hi I have run a few peripheral examples ok and now move to evaluation of ble_peripheral also.
I'm using this version of the SDK....
If I program the softdevice and...
Hi
I am using Segger Embedded Studion on Linux 16.04 operating system. I have programmed softdevice, i.e, I have provided SRAM and FLASH START VALUES and other things. How...
Here is a list of problems I found. Please fix them.
nRF SDK 15.3
Examples: logging does not work in examples. I think the problem is related to this issue .
Documentation...
Hi there,
On my application, I have multiple sensors attached to the nRF52 and I read them every 5 seconds scheduling the read inside a timer handler, then when the Softdevice...
Hi Nordic Forum!
In the past, I set connection interval min to max is 20ms~75ms, it work ok for IOS。But on Android platform, Android use 75ms as actual connection interval...
Usually if i am making C Program then i just include the library and get on to the code using documentation. this is same case when i am using STM32 , Samd and esp32
but...
Hi
For a project I want to send acceleration data via BLE 4.2 (with DLE). An acceleration packet consists of 81 values (24 bits each, total 243 bytes). My goal is to send...
Good day
I converted a Central UART example. I thought I would experiment with the "sd_ble_gap_tx_power_set()" function to see how it works.
When I include the following...
nRF5 SDK v15.2.0, nRF52840
This issue occurs on reset, most often after cycling power.
There are 4 pages reserved and 4 data pages are found. Since a swap page isn't found...
Hello. my name is Alan. I'm a newbie about BLE bonding.
because our new project needs a bonding feature, I referred to the Heartrate example(ble_app_hrs) to apply bonding...
Hi,
My current project make use of pairing/bonding and at certain times I change the attribute table. To notify the central device about this change I have added the Service...
I am working on NVMC. I was going through the product specifications for the NVMC. In that, it's given that the number of write operation limit is 181 for a block in nvm....
I'm trying to get the PPK working when connected to aNRF52840-DK, but getting the error - Error while setting up device [REDACTED_SERIAL]: Error occured when close opened...
