I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
We are using the nRF52840 SPIM0 to read 2048 bytes from an SPI slave. ( SES / SDK15.3 )
The nrf libraries only seem to support a maximum of 255 bytes, so we have compiler...
To the kind attention of Nordic support team,
We are going to use gazell protocol for some of our wireless products. Could you please point me out to the relevant documentation...
Dear All,
I am trying to integrate the simple_at example to my own application, in order to be able to configure the modem in the beginning and then run my code.
I can...
Hi,
I'm trying to use the nrf_drv_spi.c to communicate with a BL652 + MCP2515 CAN SPI custom device. I've connected the MCP2515 to the nRF52832 (BL652 module) in the following...
as others have described I run the sniffer
than go through pairing process, the encrypted packets show up as "Encrypted packet decrypted incorrectly (bad MIC)"
is there...
Hi.
currently i use the nrf connect with a dongle to connect to a ble device to read/write characteristics for testing purposes.
Now i want to do it automatically using...
Hi all,
I am adapting some examples according to my needs and have encountered something that I find strange. I am trying to send 244 bytes from computer to usbd_ble_uart...
I want to program my nRF52832 Over-the-Air but not through Bluetooth. We have a Wi-Fi chip interfaced with nRF52832 so that the device can be connected to the internet.
I am trying to read the current time using CTS. I used the example source provided by nordic. However BLE_GATTC_EVT_READ_RSP does not occur in ble_cts_c_on_ble_evt.
BLE_CTS_C_EVT_DISCOVERY_COMPLETE...
Are there any examples of sampling something like an I2C bus at a constant sample rate? I have seen issues myself with the k_sleep and k_busy_wait not giving accurate delays...
nRF5_SDK_15.2.0_9412b96
soft device: s140
Compiler SEGGER Embedded Studio
1. I have used example ble_app_uart. I connected the ble module to a device which has a baud...
Hello,
I'm looking for a little clarification on how the antenna tuning circuitry works on the Thingy:91 v1.0.0 board.
From a previous topic on the DevZone, I saw that...
I'm having an issue where I can't reconnect to a device after updating the firmware from the iOS SDK. I believe it's the issue described here in the documentation:
Since...
