I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Hi
Over the last years working with Nordic I struggled from time to time over the disconnect reason 0x3E (BLE_HCI_CONN_FAILED_TO_BE_ESTABLISHED) on our devices with Central...
hii...
i have programmed the ble_uart with twi sensor ...
complied very successfully
but while i am debugging i am getting error in void twi_init()
why and also fatal...
Hi,
Here I met a problem, please help.
I am using proxy.c to establish an data link with smartphone via mesh_GATT.
What I am doing is like this:
For TX ,
it is...
IDE: keil uvision 5.23, SoftDevice 3.0.0, SDK 12.1
Computer Platform: Windows 10
Receiving device: nrf52832_xxAA
In our project, there is a sender always advertising...
Hi,
I have a project where, I need to change the minimum and maximum (MIN_CONN_INTERVAL and MAX_CONN_INTERVAL) connection interval to higher values like 1 second and 2 second...
hi everyone!
I am developing NRF52840 with the Development Kit.
I am trying to use a GPIO to o capture a external HIGH-TO-LOW signal and then trigger a LED.
I I learned...
Hi all,
I'm currently using nRF Connect in combination with a nRF52 DK to connect to my Mesh network. So right now I have to type all my commands as HEX messages and decode...
Hello,
I'm trying to compile the Light_switch_provisioner example (Debug, Mesh 2.2.0) in Segger Embedded studio.
<t: 0>, main.c, 561, ----- BLE Mesh Light Switch Provisioner...
hello
i wanted to send message using the simple message model with some modifications from client to server periodically but didn't know from where i should start , i tried...
Hi,
I'm working with the nrf52840-DK and using the nRF5 SDK v15.2.0 Stack version.
I´ve got a working program for my coordinator (C) and my end device (ED). The C establishes...
hello dear, is there any pre defined function or library in segger embedded studio for I2C interface..? i want to make communication with digital temperature sensor(MCP9808...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Hello.
I need to solve this problem urgently.
I have now created my own protocol and are testing.
At the point of this project is the guarantee of data transmission...
Hello All,
I am developing an application using Nordic nRF_SDK_15.0.0, in which I need to make my BLE peripheral device as a peer device which will get/set data from/to...
