Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
I just bought an nrf51822 evaluation kit and a segger J-link BASE Jtag. I understand that I have to play with the SW4 swith and the U4.
I identified the switch...
Hi
I am trying to setup my raspberry pi to receive message from Arduino using C++ code. I am getting a below error message. pi@raspberrypi:~ $ sudo g++ -Wall -Ofast -mfpu...
Hi I just have a simple question and that's where the code keeps Bluetooth mesh control how many devices it has in its stack that it has provides keys to. for every time I...
hi
sdk 15.0,
IN Multilink, 15 devices is operate normally. However, changing the device to 20 causes problems.
Is there a way to fix the problem?
attached source ...
Hi,
I was trying out the long range example provided on the NordicPlayground GitHub repo, and worked great when communicating between two nRF52840 dev kits. I however noticed...
I know that the the +/-250ppm LFRC accuracy is required for BLE... but is that just for a system that receives data? Is there any need to calibrate for a system that only...
Hi all,
I am using PCA10040 with nRF5_SDK_14.2.0 and using the ble_app_uart example.
Basically I have a large array of size 18750 to send out and having read on the forum...
Hi Dev Team,
I would appreciate if you can help me sort out the errors that I am getting when doing a DFU OTA using the 52 Dev Kit to the Thingy. I basically followed...
I have an input connected to P0.18 on my nRF52832, which needs to be driven high by an external source. I am running into two problems, which may or may not be related:
...
Hi,
I have seen some posts from
Ole
and
Hakon
about the bulk data transfer. But I have some confusions which I want to clarify before implementation.
I need...
When I update the firmware to version 2.1.0, the value that TVOC reads is always 0, whether or not it is related to the thingy gas sensor requires 48 hours of operation time...
So, after upgrade to Thread SDK 0.11, I'm not able to perform DFU again. Symptoms are identical to devzone.nordicsemi.com/.../ - this time on nrfutil v3.4, with pyspinel=...
How do you pan along the Y axis using the nrfConnect version of the PPK ? I can zoom in using the ctrl and right mouse button, then pan left and right, but I can pan up and...
SDK v14.2.0 using s132
Our central should only have one connection at a time, so I set
#define NRF_SDH_BLE_CENTRAL_LINK_COUNT 1
But when it is connected to a peripheral...
