Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
I have a client device that normally is able to call ble_db_discovery_start and get the callback just fine and is able to complete the db discovery process. However sometimes...
I try to use SPI with easy DMA, in page 279 in the datasheet says: " An SPI master transaction consists of a sequence started by the START task followed by a number of events...
I have an issue with waking up SPI communication after sleep.
Befor I go to sleep I'm disabling SPI communication:
NRF_SPI0->ENABLE = 0;
NRF_SPI1->ENABLE = 0;
...
Hi is there anyone who knows if you can change the time on how often the health server model send out, the health server model is from lightswitch demo
Hi,
I wanna use nrf51822 as master which has 2 slaves: sdcard (fatfs) and adc
I set SPI_INSTANCE 0
and they don't want to work together, I mean I'd like to write some...
A time T_PINR is specified in the datasheet, as shown in the snippet below.
Does this give me an indication of the pulse width for a pin reset? If so, how do I interpret...
Not really a question, just that I find the comment misleading. In the sdk_config.h example coming with the SDK there is this piece of code:
// <q> SAADC_CONFIG_LP_MODE...
Hello,
I am trying to establish communication between Win 10 PC and nRF52 Dev Kit using pc-ble-driver . I followed the instructions in:
https://github.com/NordicSemiconductor...
RN2903 is LoraWAN module using ASCII Command Interface over UART.
RN2903 is connected with nRF52-DK.
I'm connected uart line tx, rx gnd.(cross connect...)
UART communication...
Hi,
My desire is to connect a BC832 module (with nRF52832 on it) to a UART on a controller board and then send data from an iOS app (programmed in Swift) through the BLE...
Hello,
I need two signals with a phase shift to control my motor. For some reason, completely randomly, sometimes my GPIOTE event is not triggered and i get the inversion...
Hi All,
Based on nRF52832 SDK14.2 rtc example, I want to change it to retrigger RTC Compare0, let the LED1 also toggle every 3s, instead of keeping LED1 on. I tried to add...
Hi, guys, I have an IR receiver module with 3 pin (AX-1838HS) ?
How can I use it on my nrf52832 ? I have PCA10040 development board. I don't know how to connect them and...
I need to drive a stepper motor without software intervention, since strict timing is a must.In the following image you can see the required wave-forms - the motor requires...
