I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Describe the bug I would like to inquire about an issue where when my PD (Peripheral Device) continuously sends commands without interruption, the PD encounters this error...
Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
Hello,
I would like to ask whether nRF7002-DK allows connection in STA mode to Wi-Fi with a hidden SSID and whether it can create a softAP with a hidden SSID? If so, please...
I'm looking at the `peripheral_csc` example to understand how to implement write responses. It seems for the BT_UUID_SC_CONTROL_POINT attribute, ` bt_gatt_notify() ` is used...
Hello,
I programmed the sample peripheral_uart on an nrf52840dongle_nrf52840, working in Linux and SDK v2.5.3. I had no problems using the Programmer in nRF Connect for...
I am working with an nRF5340 device and I want to understand the maximum achievable BLE throughput for both 1M PHY and 2M PHY. Could you please provide guidance on:
...
Hello,
I see in the datasheet that the nRF54L15 has an internal 128Mhz clock.
For applications that do not utilize the BT radio on the nRF54L15, is the external crystal...
Hello all ! I'm currently trying to make a scan with our custom board, I've made a custom board with our GPIO and the use of the SPI4 instead of QSPI for the 7002 -> 5340...
I set up the wifi_shell sample using a nRF7002DK and noticed that it is leaking 104 bytes of heap after each wifi connect/disconnect cycle. This is with version 2.7.0 of the...
Hello,
I am solving a problem with nRF7002-DK, I am using TCP sockets for communication. MTU can have up to 6800 bytes, unfortunately, both in STA and AP mode, the connection...
My prj.conf:
First question / issue:
I am trying to make use of the azure dps and since I'd like to use the UUID as device id i am trying to set 'AZURE_IOT_HUB_SAMPLE_DEVICE_ID_USE_HW_ID...
I am trying to make an ndef record using t4t, but it fails.
For example I'm trying to convert the example 'record_text' to work with t4t setup, and it always fail.
Is...
Setup: nrf5340dk Zephyr: ncs 3.1.0 Hi, I am trying to enable firmware update for CPUNET over Serial (USB_CDC). I enabled update for CPUAPP and it works correctly, but not...
Hello,
I am working on a custom board based on the nRF5340 SoC . When I build any BLE sample (for example, peripheral_hr or peripheral_uart ) for the nRF5340DK , the build...
