I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
The development of the custom hardware of an nRF52832 utilizing the u8g2 library has been shown to control a small display 64x48 SSD1306 driver. The prototype hardware another...
I have been migrating a project from SDK 14.2 to SDK 15.3 and have encountered an issue with UART. I am using the legacy layer with the following configurations:
I am...
Hello,
I'm evaluating nRF52811 as a long-range IC in a beaconing application.
Here's our specifications:
- The beacon must operate with Coded PHY
- The application...
Hi everyone, I know that the theoretical limit for the Bluetooth Low Energy throughput is 1 Mbit/sec, but I heard that on practice you get much lower. So I would like to find...
We were running BLE DFU bootloader for nrf52832 based on sdk 14.2; this worked fine.
We have now moved to sdk15.3 and nrf52840 as we needed USB.Our applicaton is up and...
Hello,
I have a custom nrf9160 device which requires
device stops at:
'Secure Boot: prepare to jump to Non-Secure image'
if I use this the following prj.conf:
...
Hello,
i I’m have a custom nrf9160 board. I have been using SES with j-link edu to upload firmware to my board with no issues.
Now I need to update modem firmware...
I'm trying to update my NRF52832 running s332 v5.0.0 and a stock SDK14.0 bootloader to S332 v6.1.1 with an SDK 15.3 bootloader.
I am including the flags --sd-req and --sd...
Hi All,
I am working on an NRF application that communicates with a specific mobile app, sends some measured data. Everything works fine except on some older (at least it...
Hi.
I wonder which pins are AIN0, AIN1, AIN5 AND AIN7 (on nRF52810 QFN32) ?
It seems the datasheet would tell...
I need this for a project at work.
Please. And Thank...
Hi,
I am trying to debug on nRF52840 dongle using JLink debugger and Keil uVision V5.18.0
What I have been through is here: https://devzone.nordicsemi.com/f/nordic-q-a...
Hello,
Greetings!!!
I am working on nRF52832 having SDK 15.3.0, Windows 7 and Segger Studio IDE.
Right now I am implement OTA in my custom application.
I upload bootloader...
Hello
The latest nRF_Connect_SDK documentation define an not available version of Segger JLINK. https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/doc/release...
Hi
I've tried several of the example applications on the 52840 DK board and I'm not seeing the expected services when using the iOS nRF Connect App. No matter what I run...
Hi,
can you help me out please:
I have followed devzone.nordicsemi.com/.../ and have configured as it shows.
But NRF_LOG_INFO does not work however SEGGER_RTT_printf...
