Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
HI, i would like to get device name and print to uart, but when i try to print the device name i got error character.
Here my snipet code and uart result
Hi.
My target device is nRF51822 and SDK version is 12.3.0.
I try to add Device Information Service to example "ble_app_uart_pca10028_s130"
---------- main.c (added...
Hi,
I am using NRF52832 sdk 15.2.0.
I am trying to do a device firmware update by following this link: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting...
Dears
I listed my questions below. Thanks.
1. About GPS searching and fixing, I tried Thingy91 outdoors.
- When Thingy91 connected to LTE, did LED shall blue color?...
I have a nRF52810 project which initially used the ble_peripheral/ble_app_hrs from the enRF5_SDK_15.3.0_59ac345 as a starting point. I have changed to a custom service and...
I am programming using the glucose service example source. The example source does not send any context data, so I added However, when testing with nRF toolbox, I noticed...
I'm trying to connect to my local LTE network but I can't pass the yellow and blinking LTE step. I couldn't also run the Asset Tracker project. Please tell me if you are covering...
Im trying to connect Thingy:91 and Thingy:52 to my mac book pro using USB cable to use AT config commnads. In both cases I'm getthing the following messages in the log window...
Hello there!
I was trying to look up some default values to take an RF measurement and I was wondering what the default Tx power is for the Advertising portion of the app...
I've finally worked around some funky bugs that only appeared after updating to 15.3. In my app, I had to change my clock source to RC or SYNTH to make it work (was hanging...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Ok so I am trying to integrate SPI master and slave initialization code. I am very confused about legacy and non-legacy drivers and HAL. I am getting strange compilation and...
Hi,
i am working with nRF52832, i need to us sleep.it may be do somthing and sleep 40ms,rtc wake up it and do somthing and cycle.
i see the rtc example but it may be some...
SDK: 15.3.0 Example: ble_app_multirole_lesc Device: EYSHJNZWZ (nRF52832)
I called "pm_init" to do "PeerManager". Then, a part of FLASH has been written to "DE C0 AD DE FE...
