I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hi,
We are currently working with the nRF5340 Audio DK board and aim to implement Bluetooth Low Energy (BLE) message transmission alongside the existing LE audio transmission...
I am trying to debug a BLE application on the nRF52840 DK. From what I understand, this must be done in monitor mode.
I have followed these steps:
1) added these lines...
Hello,
Hi I m trying to implement the following using mcuboot and zephyr. I have a nrf52840dk which has a external flash mx25r64 to store multiple images on the external...
Hello. I am reading up on documentation regarding measuring current on the nRF54L15-DK with an ammeter. I do notice that when we set up the board, we need to use the 2x5 SWD...
Hi there,
I attempted to change the nRF54L15-PDK settings in Board Configurator. I disabled VCOM0, VCOM1, Power to LEDs, Software Debugger and set VDD to 2.0V. I have...
Hi all,
I am working on nRF-9160 and nRF-9151, and I wanna know does Serial LTE Modem support will message function for MQTT connection or other connection?
I've asked...
Hi,
I am not familiar with the 9160DK board. I followed the same steps as the nRF Desktop Connect application guide but it always shows verification failed. I am using my...
Hi
I'm having an intermittent connectivity issue with the nRF9161 where after days of operation the device loses cellular registration and fails to reconnect.
The...
Hi,
is there a way to hide the west project from the Git view in VS code? Sometimes you just don't need to view any changes related to west and it's getting quite messy...
I am working on a Zigbee network using the nRF Connect SDK and need to retrieve the link quality information (LQI) of a specific device based on its short address. What ZDO...
Hi,
I have used nordic documentation a lot few years ago, and I am looking for BLE sequence diagrams especially the ones during pairing process with LE Secure connection...
Good morning,
currently we are on ncs SDK v2.7.0.
Because SDK v2.8.0 supports the KMU in MCUboot on the nRF54L15, I updated immediately and gave it a try.
Unfortunately...
Hello,
I searched but I can't find how to retrieve accelerometer data with thingy:53 and then send it via bluetooth to nRF Connect on phone?
Can you help me
Thank...
Hi,
I have opened sample "Peripheral_hr_coded". I have build it successfully. I click on debug. I expect cursor would start from Main function. But Debug was not started...
I'm developing my application using the NRF Connect SDK in VS code. SDK Version 2.4.2. The NRF52832f we're using is integrated into a module made by fanstel and it has been...
