SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
Hello,
I am encountering the following multi registration error when migrating from 2.5.0 to 2.7.0. I don't really have any good way to debug this as the application was...
Hi, could you please point me towards how to solve the following:
CMake Warning at C:/ncs/v2.6.2/zephyr/CMakeLists.txt:862 (message): No SOURCES given to Zephyr library...
The question is as follows：
When I read the ADS1299 data through SPI in the GPIOTE interrupt, I found that there was a time limit. Within about 50us. As shown in the figure...
Good morning
Doing the BLE fundamentals course and cant seem to build lesson 4 ex 3. Have picked up this thread BLE Fundamentals lesson 4 exercise 3 failure to build ...
Hello,
I have started working with the nRF54H20 by following the guidelines mentioned in the nRF Connect SDK Fundamentals course.
In Lesson1 Exercise2 I'm facing following...
I'm using the Thingy52 circuit in some other projects, and the built-in speaker is not loud enough for my application. I'm looking for an amplifier that can be connected to...
Dear,
We are currently developing a communication board for a client that uploads large images (~1MB) to the cloud via local and remote interfaces, and we've encountered...
Hello! I'm currently trying to scope out chips that let me do Bluetooth Classic + BLE via a UART HCI link. I came this module and noticed that it uses the NRF5340.
NORDIC...
Hello everyone,
I'm currently working on a project wherewe use the ANNAB402 and Zephyr as out RTOS. We are developing using VSCode on a Linux VM. With a new board from us...
Hi ,
I am using nrf52840 as a peripheral HID Remote control with multi-connections, and it is able to connect with all devices like phones, computers, smart televisions...
The out-of-box configuration of Thingy 52 has a 89dB, 8 ohm, 0.7W speaker.
Can I replace that with a much louder speaker such as 4W or 5W one 4 ohm or 8 ohm?
44
I am programming with the nRF52840DKs. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am currently working on integrating...
Hi,
We're currently facing an issue with Bluetooth Low Energy (BLE) range on our custom board using the NRF5340 with SDK version 2.6.1. During testing, we observed a significant...
We are migrating the firmware of our devices from Nordic's Mesh SDK 5.0.0 to Zephyr 3.5.0, starting with the provisioner device. The SOC we use is the nrf52840 and we use...
