Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
I'm developing with the NRF52840 using IAR Embedded Workbench , and implementing wireless communication based on the IEEE802.15.4 Zigbee protocol .
In the MAC frame layer...
I am new to Nordic and want to design with the nRF52840. I have read this guide:
used AppCAD to find the best width and clearance for the ground layer, but when I downloaded...
Hello, I am using NCS 3.0.2 on nRF52840. I have been using MCUBoot for a long time on my device, and it is working fine. Recently, I went through a requirement where I needed...
Hey everyone,
I've been trying to get the Bluetooth Mesh DFU Target sample working on my nRF5340 DK and running into some issues. I've read through the docs.nordicsemi.com...
Hi All,
I have an nRF5340 Audio DK which has problem with the network core. When I connect the USB to board or try to recover the board the MCU light at the bottom of...
Hello all,
I am working on a project with 2 nrf5340 Audio DK's and I want to have the same functionality of the walkie talkie demo but instead use the microphone of the...
I had a working Matter application, but due to some human error, I erased my WSL installation.
I set it up again, but after successfully flashing my code onto the Nordic...
Hi,
For a product currently under development, we need to use a counter as an RTC. We’re targeting the following commit in ncs/sdk-zephyr :
github.com/.../d7e41fd2e361ee15454a253ebec9bb37aceaf09f...
Hello Support Team,
I am currently testing the new Channel Sounding feature on two nRF54L15 boards, on which I flashed your Channel Sounding samples ( initiator and reflector...
Content: I’m working on integrating the nRF7002 EK over SPI with an nRF54L15 using nRF Connect SDK v3.1.1 . While setting up the workspace, I noticed that the Wi-Fi driver...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
I used the nRF Audio Example to build a BLE audio device. I use the test tone generator functionality. I was previously using nRF Connect SDK 2.6.1 and the test tone generation...
I am an FAE with Ezurio, we have a customer who was running through the nRF Connect SDK Intermediate training on DevAcademy and they ran into issues with AuTerm in Lesson...
## Description
On the nRF54L15DK, the measured floor current increases significantly when the GPIO is configured for button edge detection.
### Observed Behavior
* Floor...
Hi,
I am quite new to nrf's and zephyr and I'm working on a product that requires Direct Test Mode functionality. I started with the DTM sample and am now looking at how...
