Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hi,
I'm developing some projects with the nRF51822 chip and I am not able to debug them successfully any more. However, I have previously debugged correctly some projects...
This discussion has been locked. I don't know why? and I don't know how to get it back.
devzone.nordicsemi.com/.../cannot-read-max30003wing-board-using-spi-communication...
I have an Zephyr application on the nRF5340 that I've been working on. I can debug fine in SES without a boot loader. However, when I add MCUBoot into the mix then everything...
I have some code that runs on the application and network processors that uses NRF_RPC NRF_RPC_CBOR (similar to the entropy_nrf53 sample) to communicate during boot loading...
I'm trying to get setup to debug an application that uses both the app and net cores. For now I'm using the example nrf/samples/nrf_rpc/entropy_nrf53/cpunet. I'm trying: ...
I am migrating our mesh network stack to NRF 52840, which is based on 802.15.4.
I would like the code to be more efficient state machine so that I don't have to busy-wait...
Hi,
I am using the ble_blinky example as a template to develop my project, with nRF52832 and SDK 17.0.2.
My first goal is to reduce consumption, so I have changed the...
Hello,
i had a look at lwm2m_client_sample and it worked pretty well. Now my next step is to be able to send for example a 100 or 500 Bytes Payload from nRf9160 to Leshan...
Hi Karl,
Sorry, I inadvertently closed the issue.
In my understanding, with SW9 in position "VDD", VDD_nRF is about equal to VDD_HV, so the measurement should work. I...
Hi
Is there an example for BLE "Just Works" using the NRF Connect SDK for the peripheral device?
I am using a peripheral device without display and would like to allow...
Hi,
In our application we use a motor. In the case that the watchdog would trigger while the motor is running, we need to stop the motor. For this we need to set the PWM...
Hi, all,
At first, I have to say I am a newbie in programming for BLE. ^^"
I trying to development a cycling power meter, so I want to modify this CSCS example to...
Hello, Recently I tested and flashed the Zephyr program to the nrf52840DK, it works fine. While I flashed as usual last time, I saw the LED5 flashing and then the PC didn...
I would like to perform a OTA DFU in a nRF52840 DK using nrfutil. For that, I'm using the example that is in SDK/examples/dfu/secure_bootloader/pca10056_s140_ble in the target...
Hi
I have follows the following steps.
1) I build 'hci_uart' sample for nRF5340DK successfully by following guide https://docs.zephyrproject.org/latest/samples/bluetooth...
