[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
chip:nrf52840
SD:S140 6.1.0
SDK:nRF5 SDK v15.2.0
ASSERTION FAILED often appears in my firmware, connecting J-link in debugging state or turning on NRF_LOG and outputting...
Hello, I am using FDS to store three int32_t numbers. Here is my code for storing :
Here is my code for reading :
Here are the logs (stored values are the correct...
I'm having trouble sending more than 256 bytes over TWI.
nRF52840 SDK17.0.2
Used Function :
I have to send 8,208 Bytes continuously through the TWI interface in the...
Hello,
I'm trying to establish a connection with my own MQTT brocker on MQTT Box. I change the config on the prj.conf and on Kconfig file, like this :
But when i rebuild...
I downloaded the CIAA Layout and BOM resources from this page: (1.0) https://www.nordicsemi.com/Products/Low-power-short-range-wireless/nRF52832/Download#infotabs . I opened...
Hello there,
I cannot manage to activate my SIM card. Can I get some help?
* Tried outside of my company firewall? Yes, to no avail.
* Tried entering only the first...
When NRF52832 as SPI Slave, how can I know how many bytes the slave should read,the API nrf_drv_spis_buffers_set(&spis, m_tx_buf, length, m_rx_buf, length)),does not have...
Hi guys,
I am now facing a problem that I can't stop the pwm by using nrf_drv_pwm_stop.
Here's my initial code for pwm and start the pwm in the while loop.
The output...
Hello, I've tested multiple NB-IoT cards from China Mobile using the asset tracker on nRF9160 DK. The NB on Band 8 ( AT%XCBAND returns %XCBAND: 8) has no issue connecting...
I first assumed the obvious that the first library would be used with the (Visual studio) multi-threaded DLL/MD option and the second would be used with the multi-threaded...
Hi,
Currently we're developing RGB bulb which has mesh feature (nRF52832). So this done by using nRF5 SDK 15.2.0 and Mesh SDK 3.0.
We're able to control all three channels...
Hi Team
I would like to store a simple integer value in flash and read it back after a power cycle. I already studied the library Flash-manager of the nRF5 SDK for Mesh...
Hello, I'm trying to flash custom developed beacon based on nRF52811 and everytime i try to flash i'm always greeted with an error "Failed to write memory" i have attached...
Hello,
I am trying to merge mqtt_simple and gps together. Each of them is working well on Thingy:91.
1. I am using lte_lc to configure the modem and enable PSM and eDRX...
