Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
I am not sure whether this is an issue with the nRF53 Engineering Example or with the SEGGER software.
I don't see any errata describing the behaviour I am experiencing...
Hello,
Is there an option to add to thread ncp example a FEM support?? I do according to de guide on the page https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_tz_v4...
I am following this series of tutorial " BLE Advertising, a beginner's tutorial ", BLE Services, a beginner's tutorial .
The problem is after establish a fresh advertising...
Hello,
I got an error 8(NRF_ERROR_INVALID_STATE) while running ble_nus_c_tx_notif_enble function.
The SDK document shows that, the err_code is
"this API propagates the...
I'm evaluating using zephyr for an nRF52840 based design. I'm able to use the nrfx drivers via Kconfig options. It doesn't appear that there any other Nordic SDK libraries...
Hello developers.
I successfully ran the Mesh project with Light Switch example on nRF52840 devices. And I have 2 questions about this.
Question 1: How can I access from...
Hi.
I'd uesd RTT viewer before SES.
RTT viewer has the menu for saving logs.
I'm a new for SES. I'm recently using SES.
I can see log message on SES, but I don't know...
Hi,
I am just unable to find the FW ID for SD v7.2.0 anywhere.
I am using SDK 17 and s140 7.2.0 and am trying to create a DFU package to update both the Soft Device...
Hello All,
We are testing power consumption nRF52810 in system ON mode , my configurations as below,
Device will advertise for 10 sec connect with the mobile app sends...
I have already went through every step as per what the documentation has stated, but I could not be able to sniff any ZigBee packets using Wireshark. I only want to perform...
I am trying to develop a first eval / test program for the BMD-340-EVAL evaluation board using Keil. However, I don't seem to be able to download the required Keil pack. Other...
Hi,
I want to send multiple packets on a notify characteristic using ble_blanky app as baseline but only first 4 consecutive notifications are received on android side....
I would like to set the UUID below, so please tell me how to set it. 1)base UUID: 2)Service UUID： 3)Status Characteristics UUID： 4)Control Characteristics UUID： 5)Blood...
Hi,
I am using
nRF52840
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
I set tx power in advertising as below.
sd_ble_gap_tx_power_set...
