Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Hello,
I am using a nRF52DK (PCA10056). When I connect the board, the J-link drive opens up, but it does not detect on nRF Go Studio, nor is it flashing any code. I am using...
I'm using the USB CDC ACM example to write a message to a com port. I can receive messages fine except there is one problem. I am receiving the characters one character at...
Hi,
Is it possible to use two LPCOMPs simultaneously?
I would like to use analog channel 6 and 5 and if I register a RESULT Above on channel 6 it should start a software...
Good day to all
I would like to get a little more information about the function:
added in softdevice version 7.0.1.
Starting the radio in connection mode is shown...
Hi,
I'm experiencing some UART issues on nRF52832 where it seems like the peripheral is not correctly reset when doing a soft reset. After a soft reset I expect that the...
Hi,
I am using nrf25840 Dongle as NCP with Linux machine. I have used NCP example hex from " nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac\examples\thread\ncp\usb_bootloader...
How to achieve the lowest power consumption while "sleeping" but still being able to awake from an internal timer ?
For the timer I'm using the Ticker class from mbed.....
Hi,
I am a Embedded System Engineer working in a Medical device company in Ireland. I have a ublox Modem(Nina-B111), which has a nRF5xxx module embedded into it. The modem...
Dear Sir .
I have on my custom board 2 spi , spi1 and spi3.
&spi3 { status = "okay"; compatible = "nordic,nrf-spim"; sck-pin = <31>; mosi-pin = <9>; miso-pin = <30>;...
Hi，
Now I use Nrf52811 to develop a product. I use the 125k long range radio + 4dB mode.
I read through its specifications and found no corresponding...
Hi，
Now I use Nrf52811 to develop a product. I use the 125k long range radio + 4dB mode.
I read through its specifications and found no corresponding...
Hi.
I programmed the firmware in " https://github.com/NordicSemiconductor/pc-ble-driver " share folder to a nrf52840 dongle.
NRF_SD_BLE_API=6
I took the example heart...
I can send a command to a custom cluster through the Zigbee CLI, which is installed and running as a Coordinator on a nrf52840 dongle.
However, I must respond to commands...
Hello Nordic!
We are going to develop the device under the following conditions - nRF52832 - SDK11 - SoftDevice S132 v2.0.1
We are planning to add Serial DFU feature to...
Hi, I am porting an app from SDK 14.2 to SDK 16 (nrf52832) and noticed some strange behaviour with nrf_delay_ms - it is not delaying anywhere nearly long enough. I have built...
