In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Hello to all,
I am using nRF52840 DK with SDK15.0 and SES. To communicate with MS5540C I have used SPI master sample example but getting some incorrect results.
Almost...
I get a lot of error after just adding usbd source code into makefile. error: unknown type name 'NRF_USBD_Type', error: 'USBD_INTEN_ENDISOIN_Msk' undeclared here (not in a...
Hi, I am new to Nordic. We are using NRF51822 chip with S120 version of softdevice. Recently we made few changes in SDK code running on nRF51 controller chip. Is there any...
Hi, I'm using the 15.3 SDK ble_app_beacon example and want to add scan response data.
I've found some examples in the devzone, but not matching the example code in this...
Hello,
I'm currently using the nRF52840 DK and i need some help. On the other hand, i have BLE ela identifiers/sensors : elainnovation.com/bluetooth-low-energy.html
My...
I have nRF52832 running ble_app_rscs as a server, sending notification to the client every hour. I know that the client can read the values also by sending bt_gatt_read to...
dear Devzone
A disconnect error 0x22 occurred.
I know that error 0x22 is LMP_RESPONSE_TIMEOUT / LL_RESPONSE_TIMEOUT.
However, the location of the error and the reason...
I am using nRF52832 with SDK 15.2.0 for my application. The application is created taking ble_app_uart example as the base. I have modified the example to suit my requirements...
Dear,
I am working with thingy:91, v1.0.0, and running asset_tracker, I got fix location from GPS, but I am not so happy with these positions from thingy:91, sometimes the...
It seems that when I call nrf_inbuilt_key_exists() to determine if a certificate already exists, it causes a subsequent nrf_inbuilt_key_write() call to either fail or succeed...
Hi,
We are using a custom board based on nRF 52840, trying to transfer data to external QSPI flash(GD2QC).
Flash was successfully initialized and exchanged chunks of data...
Hello guys, i am trying to write a c code to read and write data to the onboard memory. i am using nrf52840 and segger embedded studio. i have used sio pins 41, 40, 04, 44...
Hi,
I already tried connecting my nRF9160 (in July) without success. I'm trying again but still no luck. If I'm right Orange has LTE-M already rolled-out in Belgium?
Anyone...
Hello,
I try to add a Thingy:91 to the nRF Cloud after I received it today. The sim card got's activated without a problem. When I try to key in my IMEI and the Pin which...
Hello I am developing based on "multirole lesc" of BLE sample project. In that project, the value of “NRF_SDH_BLE_CENTRAL_LINK_COUNT” in sdk_config.h was changed from 1 to...
