Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi everyone,
I have some questions / problems about the advertising report in the nrf52832 dev board. I'm using the example code from here : https://github.com/NordicSemiconductor...
Hi,
I've been implementing the BSP functions on a 15 button custom device based off of the nRF52832 (in a BL652 Laird Module). At a minimum I need to be able to disconnect...
Dear support team,
I'm using the demo ( thingy52-mesh-provisioning-demo).
I want to create an opcode hadler to enable/disable proxy service.
So that I can send messge...
Hi for my use-case I need the RTC in the NRF51 SoC to run continuously and uninterrupted (we know running out of battery will be a concern). Keeping the NRF51 system on 24...
I need some example code to write vendor specific service on latest development kit i.e on nRF5_SDK_15.3.
There are couple of example codes available, but in particular...
Hi
We want to put the processor in deep sleep, with minimal power consumption. When we measure, we see that the SIM is powered throughout the sleep period. Is this normal...
Dear All,
I am using the nRF52832 in conjunction with a W5500 SPI-Ethernet controller by WizNet. I already implemented a TCP server, a DHCP client and an MQTT client by...
Previously I used the MQTT example and connected it to our own server successfully. However, I want to do the same for the asset tracker application latest release (v1.0.0...
HI
I am using nrf52832 modules with SDK 11.0.0, s132.
I am able to advertise and scan the devices and display RSSI and peer address.
For my project i want to display...
Hello,
I am trying to configure a UART to use in the nrf9160. I am using zephyr's uart.h
This is a snipet of the code I have right now.
Code as it is executes successfully...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
In order to send an SMS in PDU mode, I need a Service Center Address. Normally, you can find it via AT+CSCA, but this does not seem to be supported on modem firmware v1.0...
I have a central device (nRF52832/Soft device s132) that connects to two peripherals. Both peripherals send data to the central via NUS. I have incorporated the required changes...
hi guys , I'm trying to use the ble mesh protocoll for my master thesis. I need to send a message always when an interrupt on a gpio pin occur.
there's a problem beetwen...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
