hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hi,
I am looking for the C# library for the development of Windows PC applications to communicate with nRF52 Bluetooth module.
Is there any C# library available to...
Hello,
I work with an nRF52840 DK and I want to put together the "Light switch" application with the "BLE_app_uart" application . I use the S140 softdevice, SDK 15.3.0 and...
I was looking at the specifications of a n52840 and was curious in how much power is consumed from the Analog to Digital converter in the nR52840 during the conversion. I...
Dear Nordic Support,
I am using PPI to link 2 timers (10ms & 5s) with 2 SAADC channel (AIN1 - channel 0 & AIN2 - channel 1).
The nrf_drv_saadc_init function is only called...
sdk15, SES, SD132 Hi I am using an SPI slave with nrf52 (master) I launch in the main() and I also initialize the SPI slave on main. I also configured an app timer and when...
[EDIT] The solution is posted in one of my replies.
I'd like to set up a programming and test station for the nRF52832. Segger JLink tools work fine in Windows, but I...
Good day Nordic,
I am starting to work over the ble_uart_central example, this is a project that uses bsp_event_handler to issue the events from buttons, but I cannot...
I am new to Nordic and i am using nRF52840 microcontroller, - SDK 15.2.0 - s140
When i program the microcontroller it gives me error message that my flash storage is full...
Hi,
I am using nRF5_SDK_15.3.0_59ac345 for nRF52840 DK. I am running the sdk example "nRF5_SDK_15.3.0_59ac345\examples\peripheral\twi_sensor" on nrf52840. When I am opened...
I'm currently trying to build and run the bluetooth mouse sample code on my nRF9160 DK, but I'm ecountering problems during the build process.
Shortly after hitting the...
I am having some trouble with sending messages using MQTT on nRF9160DK. What I ultimately want to to is read UART and send whatever I receive to an MQTT broker. When running...
I am trying to use sd_ble_gatts_hvx function to send custom data through BLE. I found out that for the data I am sending the function takes a lot of time to send data which...
My custom nRF52840 board uses the STmicro STM6601 push-button controller. To keep the nRF powered, the PSHOLD line must be kept high. I have a GPIO set as an output for that...
Hi there,
I am trying the test the robustness of a BLE use-case. This means that i have to create error scenarios and further observe and analyze how it's possible to recover...
Dear all i have a very funny situaton.
I can only send 1 byte in my service data when I increase it to two bytes it doesn't send. and says invalid parameters
When...
