Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
I noticed some suggestions to add Static Passkey.
I have 10040 nrf52832 sdk13.0.0 s132
The server has no IO, so cannot enter passkey from it.
Is there an example...
Hello,
I am working on NUS service S110 8.0 softdevice and SDK 9.0 and added DFU feature for the application.
First, I connected to the device using MCP from PC. It...
Hi all,
I'm trying to use the nRF51822 sniffer to troubleshoot my TI CC2650STK sensortag ble communication and the output is slightly confusing. The problem I am having...
I need to do the following when assembling a device with nrf-52 at the factory.
Add firmware onto device
Add a unique serial number for the device
Print a sticker...
i have added pwm into proximity profile example and now i am able to make beep using buzzer with pwm library.Now i want to make some sort of Tune instead of beep.
Can any...
hi,all
i use ble-sniffer_win_1.0.1_1111_Sniffer.exe,but it note as follow:
and Why sometimes not get the connection of the data? Sometimes it stop 60 CONNECT_REQ...
Hi
I use SD310 and nRF51 in SDK10 and The Ant is set HRM_MSG_PERIOD_1Hz.
I integrate a heart rate module by I2C and the heart rate data is only all I got.
But the Cell...
Hello,
while I already managed to solve a couple of problems regarding a proper handling of the DFU procedure in my previous topic here , there are still 3 problems that...
I was wondering what would be a good block size, and saw this in the documentation:
For example, if a module has a table with 10 entries, and each entry is 64 bytes...
Hi Nordic,
I am now trying to use ANT acknowledged data type in reverse direction (from slave to master), and I have some questions:
When sometimes, ack signal...
Hey, I want to save stuff to flash under the same id and key which should be no problem as shown in the documentation. But when I save it and retrieve the data only the last...
hi,
i am newer here.
i am confused in nrf_gpio_pin_sense_t i.e. NOSENSE, HIGH_SENSE, LOW_SENSE.
where is use of this feature ?
why it is required instead gpio_input...
In my application many nodes (acting as centrals) will start simultaneously, as they have common power supply. I am using s132 SoftDevice (4.0). Is the frequency hoping sequence...
Hi experts,
Can we add capacitor to the swdio pin to improve ESD capacity?
We have make some sample that add 1uF capacitor to the swdio, indeed have improved the ESD capacity...
