[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
I initially tried Segger Embedded Studio for ARM and I clicked on connect to J link device, an error occured. I wasn't sure at that time. Then I used the nRF CONNECT for desktop...
Dear Nordic-Team,
i have a nRF9161-DK Evaluation Board. On this Board the Firmware of the Debugger SoC (nRF5340 / U3) is not working. I tried to flash another Firmware onto...
running Windows 10 Pro 22H2 and using j-link v9
i tried to read firmware from nrf51822-QFAB by using " nrfjprog --readcode dump_nRF51822.hex", but it gave me an error...
I have implemented a program that sends an image's .HEX file through our custom software. The data is received and parsed by an application running on an NRF5340. The relevant...
Hi all
I am using the bluetooth central sample from zephyr. I can read the addresses of the devices but I would like to read each specific device's advertisement data. So...
I have the following settings in my prj.conf:
and getting the error
CONFIG_FLASH_MAP was assigned the value y, but got the value n. Missing dependencies: FLASH_HAS_DRIVER_ENABLED...
SDK:nRF5_SDK_17.1.0_ddde560
example: ble_app_multilink_central
softdevice: s140_nrf52_7.2.0
PCB: PCA10059 as Cental
My peripheral device's mac is 00:96:81:16:E0:9F...
Hi, I'm trying to use BLE OTA with an external memory due to my application is too big to do it only with the internal memory. When I use OTA config with internal memory,...
Since I am developing a lot for the nRF51822, I heavily relied on the old reference pages for said chip, like SDK 12.3.0 Reference .
Now they seem to be gone.
Could...
Currently nRF54L15 is being matched with LOW Q circuit and unipolar antenna. Because low Q circuit takes a lot of components and time when designing hardware. So I can remove...
We are trying to use extended BLE advertising with a nrf5340dk and are experiencing problems when trying to connect to an android phone (Android 13). Using legacy adverising...
Hello,
I noticed today that all the FOTA bundles I used to have on nRFCloud are gone !
Both the ones I added, and the "built in" ones (modem firmware).
Is this a bug...
Good Morning,
I'm currently developing an application for the nRF54L15 where I only need to send single BLE packages, therefore arising the need for keeping track of the...
Hi
I am developing an application where I need to update the BD address for advertising after each disconnection and on reboot. I know Zephyr stack has the API bt_id_reset...
