In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Hardware:
PCA10040
V 0.9.0
2015.47
Hello,
I connected the above development kit to my PC today and was prompted to update the J-Link firmware ("Strongly encouraged...
Hi,
I am using SDK16.0(ble_app_uart) program to sending dates between the phone and board.When I use my iphone xs max,it works on well.But it come out some faults when it...
I have a compile error currently: "section .heap overlaps absolute placed section .stack"
The heap size is currently set to zero.
I am guessing I am just going over the...
I keep getting this error code and while debugging I'm able to resume execution. This error seems to be thrown during my DMA transfers over SPI. Is there somewhere I can look...
I have a Thingy 91 and trying to connect it to nRF Cloud without any success so far. It is not connecting to GSM Network.
I updated both modem software and application...
At least using the LLD linker, it is possible to locate RAM segments of known size (.bss, .data, heap) at the end of RAM. Normally this allows placing the stack under these...
Segger Embedded Studios 3.52, nRF5_SDK_for_Thread_and_Zigbee_v4, nRF52840 custom board
Hi,
I use this code to start network formation on Zigbee:
zb_bool_t comm_status...
I've had nothing but trouble attempting to get the SUPL library work. I finally was able to get it working on the 9160DK with the latest modem software and GPS sample. However...
Dear All,
I am experimenting with the nRF52840 DK and the ble_app_template . Based on that project, I am trying to configure a pin interrupt on Button 1 (pin 0.11). This...
Hi,
The project I am working on involves streaming 8 audio streams (16 channels of data), and I was hoping to use the nRF52 for this purpose. Does anyone have any ideas...
When we test the BLE conducted power, we find some phenomena, when IC power is setted to 0dBm, the active power loss is similar with passive path loss, it is consistent with...
Hi,
I would like to save my project and add something like a version number to it. I use an example from nordic SDK. So in my case I use solution from ...\examples\ble_peripheral...
Hi Guys,
I am trying to enable LESC Encryption, but I do not understand how to generate keys_own.p_pk and DH keys.
The sequence is the following:
1. I receive BLE_GAP_EVT_SEC_PARAMS_REQUEST...
Hi,
We want to implement periodic advertisements on nRF52840.
We use:
1) nRF5 SDK ver 16
2) Softdevice S113 ver 7.0.1 (but this can be changed if required)
Does...
I am looking into automating the programming steps for the nRF9160 and nRF52832 for a production environment. I would basically like to do what the nRF Connect Programmer...
