Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
I'm working on an nRF52832 based IOT product using Segger Embedded Studio for ARM v4.50 on my Windows 10 machine. My project uses FreeRTOS. Looking at the release notes for...
Hello,
This may be normal behavior once correct connection management code is in place, but I want to verify since originally I was looking at 2-3 minute connection times...
I want to use a comparator without interrupt.
The measurement is not time critical.
Therefore, I chose the LPCOMP.
For initialization I use the following code:
For...
Hi Team,
We are working with nRF9160.
Below are my queries:
1. Can we use same voltage for VDD and VGPIO? If so, how can we control the VGPIO?
2. What would be the...
Hi,
I am working on a hub based on a raspberry compute module. Zigbee support is enabled by a u-blox (or Rigado) BMD340 module connected via UART to the compute module....
I have uploaded nordic thingy 91 with lte_ble_gateway program and modified it so that it can connect with 7 devices, however when i try to connect the 6th device I get bluetooth...
Hi,
SW8 (MKH-22D14-G2-B) on my board is mechanically loose. When it is in on position, the board will intermittently power off and then back on. I did not find supply online...
Hi Guys
So I am new to this whole LWM2M protocol, so my knowledge is not that good. I have the following problem. I want to start the LWM2M_client sample with the following...
In the existing nRF5x SDK, there is a type 2 and a type 4 NFC library which can be used on nRF52 chipsets. With the introduction of zephyr and the new dual-core chipset based...
Hi,
Here's my setup:
Custom board built with nRF52840
nRF5_SDK_for_Thread_and_Zigbee_v4
Segger Embedded Studio for ARM v3.52
I have built a Zigbee Coordinator...
Hi!
About my application:
SDK 16.0.0.
FreeRTOS and SoftDevice s140.
Peripheral role (buttonless dfu without bonding)
Central role NUS_C
When incoming connection...
Hi,
If I edit a project config file (.conf) how do I get SES to rebuild the project makefiles via west?
The only way I've found is to reload the project. Which seems a...
Hi teams,
Recently, I made a custom board based on nRF52833 DK.
It works fine until now, and most of things works well.
But, I cannot make the board to show logs in...
I can see advertising packets of a device using an nRF51822 in Wireshark (example packet capture here https://imgur.com/a/maV6kbb) . But can't see them in nRF Connect on Android...
