hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hi,
i have found similar posts on the forum but could not find the answer. Therefore,I think it is necessary to raise this question again.
problem: platform:nRF52832 and...
Hello there,
I have been testing on nfc-uart example of SDK 13.3.0. I am trying to pass the buffer of 258 bytes to pointer "p_pdu" and its size of 258 to "pdu_lenght". ...
We would like to have that all communications, programming, and supply related TPs and SBs should be kept for debug purposes. Otherwise, we would like to remove all unnecessary...
We're working with the NRF5340 PDK, and it's a pretty big library change from the old SDK. So far I've been unable to find out where to configure the bluetooth PHY and link...
Hi everyone,
The task is as follows. I set up data transfer using notification. I transmit ~ 83 kB in ~ 10 sec. The connection interval parameters are as follows:
The...
Hi Guys,
I flashed the ble_app_uart example available in nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_uart\pca10056\s140\ses location to NRF52840 DK board. In...
Hello,
I have been trying to get RTT to work with the nRF52810 but trying to compile the examples leads (as usual) to errors because there are a load of libraries and files...
Here is my program：
#define EXIT_PIN 31
void EXIT_Init(void) {
nrf_gpio_cfg_input(EXIT_PIN,GPIO_PIN_CNF_PULL_Pullup);
NVIC_EnableIRQ(GPIOTE_IRQn); NRF_GPIOTE->CONFIG...
Hi,
Our project is 2D-3D mouse. we are using nordic "ble_hid_mouse" application with some required changes for our application.
SDK we are using is 15.3
ISSUES ...
Hai,
we are using nRF52832 and Nordic connect for our development and testing work
we are facing disconnection issue on android after ~3min so we changed the CONNECTION_MIN_INTERVAL...
Hello,
I tried to configure Ozone for aws_fota sample without any success. I loaded elf files but one is debuging mcu boot and the other never access to the main. Do someone...
I just get one NRF9160 DK(PCA10090 0.9.0) to test the default asset_tracker application with Basis Simcard in the Oslo area. The modem firmware is mfw_nrf9160_1.1.0.zip. I...
In order to implement the standard RSA-PKCS, raw data must be signed with the private key without performing a hash.
All the CRYS functions wants either a HASH as input...
I want to drive a WS2813 led strip using a NRF52810, as NRF52810 does not have I2S, is there any other way to drive the strips. Do you know if there is any library for doing...
