Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hi,
I followed this tutorial ( https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/merging-two-ble-examples-together ) of combining UART example with other...
Hello. I use nrf52832 on Adafruit Feather board among with nrf5 SDK. As a default I can log any info via NRF_LOG_DEBUG to my serial monitor. But how can I use Serial input...
I was wondering if the standalone nRF51822 microcontroller has support for i2c. If so which pins are supported. There doesn't seem to be any reference on i2c for the board...
Hi,
I bought a custom nrf52840 board and I need to program my firmware on this SOC with PCA10056 DK debug output port. in below you can see part of shematic of my custom...
I have some custom models in my mesh application in addition to SIG standard models. As can be seen with interactive_pyaci script when i read the composition data of my device...
Hi guys.
I'm working with a nRF52832 custom board.
In my case my board communicates with the LIS3DH through i2c protocol. In the other hand based on LIS3DH datasheet the...
Sir
about the
while(1)
{
sd_app_event_wait(); //stay here until a interrupt or connection occurs...
}
During the time that there is not a interrupt and no connections...
Hi,
I've recently switched some prototype code from using MQTT to a custom UDP-based protocol. What I noticed is that if I have the unit sleep for longer periods of time...
Is it allowed and possible to change the configuration of one pin from input to output chararacteristic (and back) during the normal work flow. I need this possibility for...
Howdy,
To achieve the lowest possible power consumption on the nrf9160, it is noted that it is necessary to disable the UARTs that are not used, when in sleep mode. However...
I'm unable to write a softdevice to my nrf52840, can someone please point me in the right direction?
I was able to program the board just fine using nRFGo Studio, but I...
Hi, I am using Adafruit BLE sniffer with nRF51822 v2 firmware and I am sniffing BLE packets in Wireshark. I can see my devices advertisement data when my device is in the...
Hello,
We are using the nrf connect Android app in order to scan and connect to ble peripherals.
The scan procedure is executed perfectly as we can identify and connect...
Hi In v5 one can advertise in le_coded and then a central can connect off the resulting AUX packet.
For the AUX_CONNECT packet the inter-packet delay is T_MAFS which is...
When I read Objective Product Specification v0.7.1, it seems external pull-up resistors are required.
However, when I use TWIM without them, it works out.
Do I need...
