Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
The QSPI can be used to read/write data via the DMA registers.
The QSPI interface is used with code is running from the XIP memory area.
Assuming the XIP and data areas...
Hi Nordic Engineer,
We want to interface NRF52840 with MTK7628 over UART. Is there a client library for nrf52840 which we can integrate with our application which runs on...
Hi!
I am trying to get scan_req_notification to fire notifications when central devices issue scan reqs but without success until now. Here is my code:
Env: SDK15, SES...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
The SDK 15.3.0 and 15.2.0 Documentation references ANT + BLE Serialization example in " \examples\connectivity\experimental_ant_ble ". In the SDK I only found " ble_connectivity...
Hello,
We are referring to demo project ( https://github.com/NordicPlayground/nrf52-ble-image-transfer-demo ). This is quite matching for our requirement. However we have...
What is the default state of the GPIOs after reset, until my code has a chance to configure them?
Are they all Input/HI-Z? Is there a place in the manual that specifies...
Mesh DFU works like:
if(fw_updated_event_is_for_me()) update_ and _relay(); else relay();
Is there a way to change this behaviour to:
if(fw_updated_event_is_for_me(...
Hi,
I'm working on porting a project from an NRF52840 to an NRF52832. Apparently I screwed up something somewhere and I can't compile the project anymore. I'm using GCC...
Hi,
I working on a project that need to communicate with other mcu by SPI, the communication is work, but I have question about the start and stop of communication.
...
Hi,
I just met some difficulties to implant more then one service into my project. The project was developed based on hid_keyboard.
The project can work normally when...
I am using 2 nrf52832 boards to talk to each other through UART. One is programmed to the central SDK example and other other is peripheral. In the code, i incorporated 2...
Hi, I got the issuse about the connection with nRF52810. I used nRF connect to connect the nRF52810 device via Android,but it isn't easy to connect successfully.The nRF log...
