Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
I have been able to get all the MPU based projects to work from this Github site (which has been very helpful!) with the exception of this one.
The accelerometer values...
For a device that has APPROTECT enabled, it is required to use nrfjprog --recover to re-enable access.
What is the mechanism that nrfjprog uses to perform the --recover...
With the nRF52, is the RTT functional when APPROTECT is enabled?
I would expect not since the RTT relies on memory accesses which should be disabled with APPROTECT
Hi,
In SDK11, it was possible to call app_sched_execute() from a function that was itself called from the scheduler:
void app_sched_execute(void)
{
void * p_event_data;...
If you dont have an external 32Khz crystal for the nRF52832, besides the higher power consumption, are there any other issues ? e.g. CPU starvation affecting my app during...
Hi all,
I work with a nrf52, my project send and receive Beacon data.
when i work only with 2 card all works fine but when there are several transmitter and 1 receiver...
I've got an nRF52 application which is based on the nRF OpenMesh github.com/.../ but has been vastly customised. The application either acts as a mesh device and allows a...
As the title，I recently want to use nRF51822 to communicate with SmartCard in ISO7816 interface. but I don't know how to do this.Can anyone share the example code online ...
Hello,
I am using the nrf sniffer from adafruit to pick up ble packets from my NRF52. Everything has been working fine for the past 3-4 months. Yesterday I wanted to test...
I'm trying to create a HID over GATT device that is not a keyboard, nor a mouse. About a week ago, I came close by being able to read some data in an OSX app from the device...
Have project setup to read values from ADC and then run fft_process. Then print them out over uart using NRF_LOG_* statements. However after we call the arm fft functions...
Hello, I am using nrf51822 and SDK11, dual bank dfu ble, S130, 2.0.0.
I made dfu zip file and I modify firmware_crc16 value to the wrong one.
And I zip it again.
But...
hai
i am working with nrf51822 and mbed .
in my application i have requested one page in flash for data store using pstorage.
pstorage_module_param_t param;
param...
Hi,
I'm trying to use NFC type 4 tag on nRF52 side (PCA10040) and poll and read it on Embedded Linux using neard [1]. I'm not an expert in NFC area, so I could be wrong in...
I am migrating a project from SDK 12.1.0 to 12.2.0. According to this question the RAM base needs to be defined in ble_stack_init(). The examples that come with SDK 12.2.0...
