GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
This topic has been done to death but I was hoping for a bit more detail with regard to enabling DC-DC while using S110 V8.0 for BLE, but on second revision hardware nRF51822...
I'm working on a project and want to use the battery service to do that, send notification when the battery reach to 75%, I decided to use the battery service found on the...
I am a beginner in nrf boards. I was using mbed online for programing the first few programs. I wanted to setup a tool chain on my machine and installed the nrfgostudio and...
Hello everybody,
I'm developping an application using nRF51 Development Kit with S130 softdevice and I'm looking for the power profile of scanning event. I understand that...
On 51822 : tt seems to me that I need to call sd_ble_gap_adv_start before I can use uart...
Do I also need dtm_set_timer etc to start uart ?
Thanks
Thomas
Hello Everyone
I have an issue when reading the value of an attribute using sd_ble_gatts_value_get, where if the connection has been lost, the call will block for ever...
Hi,
I have product that uses the S110 stack for communication. However I really need to lower the energy consumption and I am trying to make a minimal BLE implementation...
It's not clear to me from the documentation what a 'user' with regards to the APP_GPIOTE_MAX_USERS define used when calling the APP_GPIOTE_INIT macro.
If I would like to...
Hello, Nordic staff,
I work at UART(Host PC_A)<->BLE(S110)<=> BLE(S120)<->UART(HostPC_B) product(like a SPP profile of Classic BT) using a S100 and S120.
I use the flow...
I recently purchased the nRF51 DK and the NRF51-DONGLE. Would you please advise how to use these two devices. My goal is use the nRF51 DK to programmatically control the Reset...
When I call nrf_gpio_pin_set(LED_1), the LED is turned off and when I call nrf_gpio_pin_clear(LED_1) it is turned on. Is this expected behaviour? I can't find any schematics...
Hello,I changed nrf51822 firmware and NrfUart API .Now nrf51822 dongle and beacon can comunicate between them .Beacon transmit notification data and can receive a command...
Does nrf52 SoC consumes the same current at different supply voltages(assuming similar operating conditions) ? For eg what is the difference between operating the nrf52 at...
Hello,
I've just received a new nRF51822 EVKIT and I'm trying to run the blinky project example.
I have installed uVision 5.11.10, the Segger Drivers and the Nordic SDK...
Hello,
I want to use a mobile Bluetooth as a transmitter and the dongle of nrf51822 s110 (pca1000) as receiver using master control panel and just read the RSSI values...
