if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hi All,
I am able to successfully connect to nrf51822 EK using BlueZ 5.12 and can read many of the characteristics except for the temperature value.
I understand that...
Hello
I have a project about voice communication.
Trying to do bidirectional voice communication, is there any possible to work on nrf51822
It means whatever via Bluetooth...
Hi,
I have version 2.0.0 of Evaluation Kit. I was waiting for the new SDK and SD 6.0.0 but I have seen the warning about hardware versions. I have to finish a SoftDevice...
I'm a noob in this alley! it is my first time working with Nordic products. In the past I used Energy Micro and ST Micro.
I downloaded Keil 4.x from ARM website. Then I...
Hello,
I am developing a project using nRF51922 and S310, and the project is built using SDK4.2.2 with the modifications mentioned in a document called "nRF51922 - ble...
We are looking to understand the internal working of the nRF51822 firmware (MEFW_nRF51822_0.9.0_firmware.hex). If someone can share the original code or the basic block diagram...
Hi folks,
I want to match my IFA PCB antenna to the nRF8001. As Harald recommended a couple times, I am going to measure the antenna of the final PCB with a Vector Network...
Hi All,
I use the 51822 DK to do the current measurement and do as the DK user guide 5.1.8 current measurement.
I just use the __WFI() to make the 51822 get into idle...
Hi!
I must match NRF24L01 to 40+j48 ohm antenna. This is not my design, so
no possibility to change. I have PCB antenna, that was measured to be 40+j48 inside
enclosure...
I have some non-volatile storage routines that I have written before, but the new SDK V5.0.0 has this pstorage module that is supposed to replace it, right? How do I migrate...
I use 51822 nrf6130 "device_firmware_updates" example to update AP. When I build "dfu_dual_bank",the update will success. But when I use "dfu_single_bank",the update will...
Hi,
Do the nrf_temp functions, nrf_temp_init() and nrf_temp_read() only work for the nrf6310 board? Are there equivalent functions for the EK?
Thanks,
Mike
I have been trying to connect a nrf8001 device to a Android 4.3 device and it is discovered ok but fails when it tries to do a service discovery. After some deep digging I...
I am having the same basic issue that is described here:
https://devzone.nordicsemi.com/index.php/setting-advertisement-parameter-s-for-custom-profile
Including the error...
