Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
I am trying to get an end to end BLE application working. I have an nRF52832 board that is running peripheral_uart. It is advertising and sending a text stream to the connected...
Hi Nordic support
We have ealier used your legasy SDK16.0 on nRF52840 where we where programming our device serial number in the UIRC area.
NRF_UICR->CUSTOMER[0-4] where...
Dear,
I was trying to flash a custom board using a nrf5340 module (Raytac MDBT53-1M) threw P20 connection of a nrf5340-DK like described in https://infocenter.nordicsemi...
I have discovered a serious issue with Bluetooth connectivity on iOS 26.
My device use nrf52832 and sdk15.3, it consistently disconnects just a few seconds after a successful...
Hello, i am already 1 week trying to make tracing working. I have NRF54L15DK and SEGGER J_TRACE PRO. I solder trace port on the board.
I did enable => nRF TPIU in nRF KConfig...
I've tried to compile "hello_dect" example using v2.6.1 toolchain and v2.7.0-rc-2 SDK. The sample code is present so I assume the SDK is correct version. However it fails...
Hey folks, I'm trying to use SPI00 instead of SPI20 to achieve higher frequencies and driver fails to initialize no matter what I've tried to do on NRF54L15-DK. Here are relevant...
Hello,
I have 9 sensors based on NRF54L15 working as GATT server. I push around 100 bytes every 15ms from all sensors to the central hub. When i connect all nine of them...
Hi everyone!
I am developing device based on nrf25833 mcu which should transmit data to android devices using ble characteristic notification mechanism (data received...
Hi!
Recently I bought this device (v1.1.2) and I was very happy about it until I tried to verify the current and voltage readings. Tried two multimeters and they both agree...
I am porting and existing app to nRF Connect SDK 2.7.0 from 2.6.1. Using sysbuild, MCUBoot and the app are building and I am able to load the firmware onto the PCB and it...
Hello!
I've just come into contact with the nrf54l15. On the customer's board, it is necessary to change the NFC pin to a regular gpio, and they following the previous nrf52...
Hi Is it possible to configure project to use simultaneous multi image DFU and serial recovery over USB? I would like to be able to update both cores using dfu_multi_image_XXX...
I have an LED connected, and I want to use PWM, but enabling it adds about 700 µA of passive current — both when the output is high and low. However, if I set the duty cycle...
