In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Reopening this issue from three years ago
as the original question was not answered.
So I had this line of code after sd_softdevice_is_enabled 'returns' false
but...
I am trying to communicate with multiple devices using ESB. The host device must queue data in the TX FIFO as ACK data before receiving the data. I want to keep data queued...
Hello! I am developing an application under the SDK V2.9.0. Now I am trying to set up a simple project with a sysbuild, Mcuboot and a partition manager. Here is the file tree...
Hi,
I’m currently using nrfx libraries when there are no equivalent options in Zephyr drivers, and I found similar drivers with the nrfy prefix. What are the differences...
Hi
I would like to use DeviceTree in VS code. The VS code had installed "nRF Connect for VS Code Extension Pack" and tools chain.
But I can't see any file in "DEVICETREE...
Hi Nordic DevZone Support,
I am facing an issue with my custom PCB using the nRF52840 microcontroller and Zephyr NCS v2.6.1 . The same firmware works on other PCBs , but...
Hello, I am working on nRF52840 and using nRF Connect SDK v2.9.0.
I want to know how I can configure the UART to be half-duplex tx or half-duplex rx.
I checked the APIs...
Hello Nordic supporters!
We are developing a system using BT Mesh alongside a software DALI protocol driver with certain timing requirements.
Right now we're trying...
Hello,
I am trying to build the Wi-Fi Bluetooth LE coexistence example using the nRF54L15 DK and nRF7002 EB, but I encounter the following error: zephyr_pre0.elf section...
This is not a support request.
I just want to share some code that others might find useful. If I post it here then they might find it.
The current RADIO_TEST example...
Hi,
I'm trying to use RTC to generate interrupts at every second. The rtc event handler is below:
In the RTC examples, nrfx_rtc_counter_clear is used to reset the RTC...
We are using the nRF5340 with the nRF7002 Wi-Fi module on our custom board. Our application periodically sends data to a server. During continuous testing, we encountered...
nRF Connect SDK with VSCode has suddenly stopped working.
Problems
When I try to create a new application by copying a sample, it says "no samples available".
When...
I created an application that stress-tests wifi scanning and neighbouring cell scanning, on nrf9151 with wifi extension board. Wifi network scanning and neighbouring cell...
I am using peipheral lbs sample and modifying it for my project use. By default it doesnot has pm_static.yml where addresses could have been defined. Once i build the modified...
