Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Dear all,
Hi, I'm Eric.
I m studying spi communication used nRF52832 base on SDK 14.2/example/spi.
That examsignal is below picture 1.
But I want to delay between...
Hi--
I noticed something rather peculiar on the built hex from segger that is programmed onto my nrf52832 chip (firmware image).
The hex looked as expected, until i got...
My ble_peripheral is bonded to ble_central, How do I upgrade at this time ? If you still use the mobile phone APP to upgrade, you need to erase the binding information, and...
Hello,
I encountered a problem when installing nRF_connect on a new computer. As shown in the picture, the attribute "middleware" of null could not be read. Opening all...
I am using as template the MQTT sample app from NRF Connect 1.3.0, for which I want to create my own application modules, I have added the .c files to src, but I am having...
Hello,
We are using the Serial port library with two UARTEs. It defines two instances of the serial port interface: one for receiving data, and one for sending data. After...
Subject pretty much explains the problem. One can just get power from a USB interface, but if I plug our nRF52840 into such an interface, it does not appear to boot into its...
I am trying to use serialization to connect an STM32F4 to an ISP1705. My goal is too connect to other BLE devices and read some measurements. I have tried a few of the examples...
I'm using an example project of the secure serial bootloader (pca10056_uart_debug) and changed some configuration for my custom board. I added RTT debugging and changed uart...
Hi,
One of our projects will use either a LFXO or the LFRC depending on the accuracy.
The product will be exposed to temperature differences ranging from approx. 0 ...
Hello!
I handle mpu6050 sensor in SDK v14. Output of sensor values was successful. And I'm going to use this value to get the angle of the sensor.
The code below is to...
I am using NRF Connect 3.5.0 to program PCA10059 but receive the following error on some dongles when using JLINK programmer
Error while probing devices: Error occured when...
Hi there,
I purchased the nRF52 DK, and I am going to study how to use basic tools.
However, there is a problem with recognition between the computer and the nRF52...
Hello! When I start the s132 device, it freezes from time to time. In debug mode, it does not exit the saadc_init () function;
I connected "hardfault.h" and "hardfault_genhf...
Hi,
I am using nRF52832 , and sdk 15.2 version. I am trying the start the advertisement using timer , once it is connected it should send the data , and should disconnect...
