Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Please tell me how to change the communication data length of BLE communication to 244 bytes and shorten communication cycle. Thank you.
I am using the version of [nRF5_SDK_15...
I know that there is a similar question here but the problem that the question is pointing on is not solved. Even in one of the answers is mentioned:
Now I found that...
When I run the example "ble_app_hrs_rscs_relay_pca10056_s140" on the development kit while debugging, then the SVC call for enabling the softdevice will stop at Address x8C4...
Hi! I want to implement at BLE switch(PTM215B) to a nRF52 DK, The switch sends advertise messages with switch status data. So i want to create a simple central that scans...
nrf52832 code always block at nrf_spi_event_check, my application include a app timer 200s period, after timeout, drive spi to get a RF sensor for sending some data, and also...
I am working with the nRF52832, SDK14.0.0. I want to perform a flash write on a watchdog reset to save the current state. However, the watchdog resets after two cycles of...
I've used the 'secure_bootloader' project, updated with the public key, to flash on the DK. The project 'ble_app_buttonless_dfu' built and packaged as zip can be DFU'd with...
Is it possible to _send_ multiple packets per connection interval, using the pc_ble_driver (and a nRF52 or nRF51 DK) in BLE CENTRAL role?
I found some answers on the devzone...
Hi, I developed a static library including drivers for spi, twi, gpio, adc and few others. Now when I create application and link my library it works ok as long as I am using...
Hoping to get some help. Using swift3 and xcode 9.3.
I can write data from iPhone back to nrf52 peripheral fine if it is a Dbl.
When I try to write a UInt16, it crashes...
I plan on using the nRF51 Dongle meandered antenna for a design involving the nRF52810. Since the nRF52810 has an internal balun, does that mean that L1, L2, C5, C4, L3 and...
hi,
i have a custom board with nrf52832 as it's core. i want to program with st-link v2 programmer.
i am using sdk 14.2 and soft device s132 v5.0. on target location we...
Hi guys,
We have tested the mesh range in the nRF52840 chip (max tx power) in LOS and we got more than 200m.
W're planning to use the mesh network inside hangar with a...
