Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
What is the designed (/actual/required due to the specification) behaviour of the Bluetooth stack S110 when notification packets are queued and the CCCD controlling the attribute...
I am looking into using Internal RC instead of External Oscillator (with softdevice on).
The function ser_app_hal_hw_init() uses Xtal clock source by default.
...
Hi, everyone. What is the meaning of datasheet "section 8.5.7 Antenna matching network requirements"->15+j85 ?
Whether is that we can caluate the 50o with the data?
bonjour , j'ai essayé de communiquer deux pca10028 en utilisant l'exemples " transmitter_pca10028 et receive_pca10028 " mais l'experience a echoué je sais pas pourquoi sachant...
Hello,
I'm testing current time service client example on SDK 8.0.0 with iOS.
After connected the devices, iOS show confirmation to pairing.
When I canceled this or...
After enabling and starting the watchdog timer (RR0), how can it be disabled?
This following code does not work :
NRF_WDT->RREN &= ~(1 << WDT_RREN_RR0_Pos);
Neither...
Hi,
I use s120 stack and ble_app_multilink_central
I use function sd_ble_gattc_primary_services_discover(p_client->conn_handle, start_handle, NULL) for discover services...
The sniffer software doesn't seem to find the device on either of two different PCs here, and I'm not sure what we could be doing wrong.
The installation steps were the...
Hello,
I have recently got a n5 start kit nRF51422. I went through all the set up procedures in the user guide, installed all the correct programs/drivers etc.. My unit...
Hello.
I am looking at the schematic of the nRF51422 USB dongle development kit. The pin P0.30 of the microcontroller is attached to ground. As the pin could potentially...
I'm writing a PC utility in Visual Studio to connect to BLE devices. I'm using the PCA10000 and MasterEmulator.dll. I'm able to discover the services and characteristics of...
Hi NORDIC
I download the example of multilink central (S120) into nrf51822 . I do not know why it can not work ? My SDK is s110_nrf51822_7.0.0_softdevice . Please help...
i am very confused about how to count pulse by using nrf51822? I am going to make a heart rate counter, but i don't know how to config registers to achieve this function....
I can't get a simple application, no soft device, to debug on the nRFDK 10028 board using the I-Jet. I am using the debug in and powering the device from an external power...
