Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hi
For a low power product, I need the nRF54L15 to wake up periodically with very low consumption in between. In the deepest sleep mode there is no RAM retained and so the...
So I've been trying out the nRF9161DK, and had a lot of problems creating builds with the included samples. Mostly CMAKE errors.
Guess I'm missing some basic knowledge here...
As shown in the figure above, if I need to modify the time interval of OpenThread's Link request or parent request, how can I do it? Thank you
NCS 2.6.0
NRF52840
Hi I am trying to add multiple services to the custom_ble_service tutorial example right now. When I try to create a second ble_cus_t instance 'mcus2' by calling BLE_CUS_DEF...
When I set CONFIG_BT_FIXED_PASSKEY=y in prj.conf. The following warning messages are generated by west build command.
CONFIG_BT_FIXED_PASSKEY is enabled
A fixed passkey...
I'm trying out to operate an external flash and first thing to try before anything was the spi_flash sample.
*** Booting nRF Connect SDK v2.8.0-a2386bfc8401 *** *** Using...
I have a question about tasks with different priorities and interrupts.
So for example I am using I2C and UART with different tasks and suppose I2C is in the midst of transaction...
Hi all,
We are working on a project that uses the nRF5340 and nRF7002 combo. In our application, the device enters a low-power mode on the nRF5340 during sleep, with the...
Hi,
As the subject, when i connect to the Windows with the cable connected with VDD side, it will not show up Jlink in Windows.
What should I do to reset the Nrf5340 ...
Hey everyone, I am looking for big size capacitive touchscreen for my next project so I do found with resisitve touch using FT810 EVE graphic controller with nrf52840( https...
I was trying to get a simple Zephyr project to build and run on the Arduino Nano BLE 33 which has a NRF5248.
In VSCode with the NRF plugin I select "Add build configuration...
I have a PCA10056 (nRF52840 DK) and while programming it with a UART example from the nRF5_SDK_17.1.0_ddde560 using Segger Embedded Studio for Arm 5.42a, it will not show...
Hello, I have one smartphone with Android and one ith iOS with NRF connect application and I can't see, only on iOS, the Primary and secondary PHY used by my advertiser device...
Hi everyone,
We have devices using the BLE module (nRF52) deployed in clinics for testing. They have been functioning without issues until recently when we noticed occasional...
