I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
Dear Nordic team,
i am stilll struggeling with the GPIO set-up in system off mode. It seems, that both GPIO_INT_EDGE_TO_ACTIVE and GPIO_INT_LEVEL_ACTIVE are working fine...
I am getting started with the nrf52840 dk, and I am unable to clear the flash with the Quick start . Here are my logs: 2025-09-24T02:11:29.285Z INFO Initialising the bundled...
Hello,
I'm trying to connect an SPI device on the nRF54L15-DK kit. The Nordic support page says it needs to be configured using the board configurator , as seen in the screenshot...
Hello,
I would like to ask if it is possible to upload a program to nrf7002_DK where it will be possible to select Wi-Fi STA or AP mode? I tried to connect it, but the compilation...
So I have a timer interrupt setup which triggers every 1ms in the interrupt I give the semaphore with The interrupt triggers correctly as seen from logic analyzer this should...
Hi,
I’m working with the Matter Door Lock sample in NCS 3.0.2. With the default PRODUCT_ID = 0x8006 , everything works as expected: commissioning to Apple Home and Google...
Getting a Precise data bus error - BUS FAULT, when sending a http POST request to an https sever over tls. Cannot decipher the exact instruction address as on enabling CONFIG_DEBUG_OPTIMIZATIONS...
Hi, I have a device using nRF5340+nRF7002. I am storing multiple wifi credentials and using auto connect. I have some questions: 1. Using auto-connect, how does the SDK/wifi...
through RTC i am trying it but it is not happening can you give any propre example one for the sleep mode enabling and wakening up from the sleep mode.
Hi,
I'm using the peripheral_hids_mouse example from NCS v3.0.2. What's the correct way from SC(Secure Connections) to enable Just Works pairing ?
Thanks!
The nPM1304 requires the CC1 and CC2 pins to be connected to the USBC port. Can they be left open/grounded on the IC side?
The problem which arose is that CC1 and CC2 are...
Hi, I'm looking for clarification whether the DECT NR+ modem firmware supports GNSS. Legacy docs say it doesn't, but there is no mention of it in current docs. Based on that...
Hi,
Issue
With the official nRF21540-EK + nRF54L15DK setup, my app/config works: advertising, connections, and PA/LNA behavior are all OK.
On my custom PCB ...
I am attempting to do channel sounding with one initiator and two reflectors. Switching between reflectors, by connecting to each in turn, does work, but it is very slow....
