In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Hi guys,
I'm fairly new to this kind of stuff and I'd appreciate if someone could point me in the direction of how I would go about taking the data being transmitted by...
Hi nordic,
I am using SDK15.0 (NRF52840) to design a watch producation which needs pairing. I have a problem that if NRF52840 (peripheral ) has been paired with a smartphone...
I want to get the RSSI of a connected device. The sequence will be as follows:
int8_t *p_rssi;
uint8_t *p_ch_index;
sd_ble_gap_rssi_start (m_conn_handle, BLE_GAP_RSSI_THRESHOLD_INVALID...
Setup: nRF52840 DK nRF52 SDK v16.0.0 s140 v7.0.1 When I attempt to use the nrf_crypto library for AES 128bit ECB encryption I keep getting
NRF_ERROR_CRYPTO_CONTEXT_NOT_INITIALIZED...
'm sending a publication set message (0x03) from an iOS app to an nRF52840 board using the light server example in the latest SDK. This works and I'm able to receive messages...
Dear All, I would like to know which is the better GPIO configuration to drive a LED for extremely low power consumption. We have a board with nRF52832 SoC with GPIO connected...
Hi,
I have Android (8.1.0), and installed nRF toolbox 2.8.0. To update firmware using .zip file.
The DFU Upload returns error:
Unfortunately, nRF Toolbox has stopped...
The 3GPP Release 14 introduced new, third power class of 14 dBm for NB-IoT devices. Is it possible to assign nRF9160 to operate at the lowest power rating class, the 14 dBm...
Hello everyone,
I am working on a project where I need to interface an NFC reader (trf7970a from TI) to an NRF52840.
I got everything working fine, but I have a major...
Hello,
I am running S140 on an nRF52840 custom board. While doing some power profiling, I noticed a spike of current of ~15mA when going from sleep mode to waking-up due...
I've created read onle characteristic called "log". In main.c i try to update it by calling : ulogd_characteristic_update(&m_ulog_service,Log_Data_arr)
But nothing happens...
How can delete individual peer bonding data without to affect the rest bonds:
-currently connected (after disconnect)
- some peer by providing RPA (assuming RPA matches...
Hi,
Is it possible to enable the transmission of 2 bytes of preamble and use the TIFS register to force a delay to transmission when in proprietary 2Mbps mode?
Thanks...
Hello, I'm using SDK 16.0, softdevice s132 v7.0.1, I'm sending the device to SystemOFF and configuring a pin to wake it up with
nrf_gpio_cfg_sense_set( IMU_INT2_PIN , NRF_GPIO_PIN_SENSE_HIGH...
