What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hi all,
I am using the S332 softdevice for dual ANT/BLE stack in SDK v14.2 bundled with bootloader_secure_ble, which was apparently power optimized in SDK v15.0.0 (see my...
I have made a custom board based on the raytac NRF52840 module (MDBT50). When i load in the USBD CDC example (SDK version: 15.2), The device is not detected. There is no output...
Hi, I would like to build a mesh network with ANT so I tested the ANT scan and Forward example for nRF52832. And the current consumption is around 5mA, is this current normal...
As in the title, I installed 64bit nRFgostudio, however it crashes just after opening with the log below. It opens fine when I do not have my Thunderbolt 3 docking station...
Hi,
How can I send message from servers other than 0x105 and 0x106 to client?
I receive status message in client from servers 0x105 and 0x106.
I can send message to...
I'm trying to use the SDK 15.0 saadc example with a potentiometer on AIN0, and I'm getting weird values. Left pot pin connected to VDD, right pot pin to GND, center pin to...
Hi Nordic:
I want to add some rtt log in the bootloader code, so I make bootloader flash start at 0x77000, size is 0x7000, and my application's FLASH_PH_SIZE is 0x77000...
Hello, I read in the documentation how to create a model, in the client model, which defines a struct: simple_on_off_msg_set_t {uint8_t on_off, uint8_t tid}. I do not understand...
See: http://www.keil.com/forum/63929/
Everything here refers to J-Link, eg devzone.nordicsemi.com/.../a-working-demo-of-monitor-mode-debug-mmd-on-sdk-15-please
and Google...
Hello,
I am wondering that what exactly are the differences between libmbedcrypto.a and libmbedcrypto-software.a?
I read through the SDK documentation about the opethread...
In SDK 15.2 in ble_gap.h
#define BLE_GAP_SCAN_WINDOW_MAX 0xFFFF /**< Maximum Scan window in 625 us units, i.e. 40,959.375 s. */
#define BLE_GAP_SCAN_INTERVAL_MAX 0xFFFF...
Hi Everyone,
I'm using nrfutil in an arm cortex a8 running Debian 9 with kernel 4.14.49. The processor is connected to a NRF52 dongle through USB. I'm trying to flash (using...
Hello ! My custom board is working fine (with the last programm I flashed into), but I can't access it with my debugger and I can't flash it again. When I try to flash it...
This is my Output, Looks good but not working/
Preparing target for download Executing script TargetInterface.resetAndStop() Reset: Halt core after reset via DEMCR.VC_CORERESET...
I am using nrf52832 with latest version of s140 softdevice.
I migrated a project, that was used on a nrf51 chip, to the latest sdk version.
The problem is that the measured...
