I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hello everyone,
I want to measure current of the whole board, I follow the instruction of nRF52840 DK , which suggest not to use the USB connector to power the board.
...
I am using Rowley CrossStudio 4.4 to debug my project. I can program and step through the code just fine, but I can't seem to get any debug out put on the Debug Terminal....
(1) Production Programming using CLI:
We are entering pre-production for a design containing an nRF52810 (on Rigado BMD-330 module), and we need to know what the CLI command...
Hi,
I was referring the timer example code for PCA10040. I wanted to include the timer code in my ble peripheral code which uses custom GATT service. Can you help me with...
I see that the nRF9160 DK has both cellular and BLE capabilities because it has both a nRF9160 SiP and nRF52840 SoC. Wouldn't it be optimal to combine both cellular and BLE...
Hi There,
The attached image shows the part of the schematic responsible for the enabling of the QM14501. I was wondering if there was a particular reason that the mosfet...
Windows 8.1, 64bit PC
I have a nrf52840 app that works from "SEGGER Release 4.30 Build 2019101800.40379 Windows x64" on the DK 16.0.0, and from " nRF Connect for Desktop...
Hi there,
I want to implement the BLE dfu in nrf zigbee and thread sdk but there are no examples provided in the sdk and if i try to use the files from nrf 52 SDK for...
Similar to this ticket , we are no longer able to connect to Verizon using a Hologram SIM after upgrading modem firmware from 1.0.1 to 1.1.0.
I'm attaching a matching console...
Inside gps_controller.c
We issue the following instruction to begin searching for a satellite fix.
k_delayed_work_submit(&gps_work.work,K_SECONDS(CONFIG_GPS_CONTROL_FIX_CHECK_INTERVAL...
Hi,
We are atempting to get DFU over UART working in our project, but there does not appear to be a bootloader project in the 16.0 SDK for this configuration. What would...
Hello, I want to put extra authentication when device is preparing for boot loader. I found callback "ble_dfu_evt_handler". I think inside case BLE_DFU_EVT_BOOTLOADER_ENTER_PREPARE...
Hi,
I am using nRF51822, S130, SDK12.
Now trying to add a level of security with a static passkey, I have done the following adaptation to my code -
Added to void gap_params_init...
