Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Hello,
I am testing the capabilities of Thingy:91, the first day I could see data in cloud (temperature and other sensors + GPS).
Today usage of SIM card grows up but...
Hello,
I'm trying to setup a new project and start experimenting with the nRF51 series. I'm a little confused about the needed files I have to add on the project to get...
Hi:
SDK version: SDK 13.0
MCU: nrf52832
For the purpose of saving power, the peripheral disconnect the BLE connection in the program when there is no data transmission...
Hello,
I am using nRF52832 EVM board with SDK 15.3.0 in SEGGER studio IDE, win 10.
When I am implementing sd_nvic_SystemReset(); in my code, that time i am not able to...
I have a custom board based on QIAA Reference Layout 1.1 Variant 6.
The application is built with Zephyr without bootloader and is placed directly on address 0x0.
When...
Hi, I'm designing nRF52832 custom board, on 'single side' pcb.
To make VDD and GND lines connect, I used 4 jumpers, which have 0 ohms.
I designed with nRF52832-QFAB reference...
I used the ble_app_uart for pca10040e successfully on the DK52, now I'm trying to port that project onto actual nRF52810 chip.
This is my build configuration on SES (Segger...
Hello Nordic Support Team,
The question I have is simple.
Can I use the pc-ble-driver with the ble_connectivity_s140_usb_hci example found in SDK15.3.0?
If not why?...
Is there any public documentation on the LTE Modem hardware API for the nRF9160?
I'm interested in porting an embedded operating system written in Rust to the nRF9160 and...
Hi,
I am using ncs 1.0.0 in nRF9160.
I have enabled UART 2 interrupt during initialization of the uart as below and it works fine.
To reduce the power consumption...
Hi,
Using the Thingy app on my iPhone works fine.
However, I would like using my iPhone as a gateway (thingy:52 -> iPhone (BLE -> Internet) -> nrFCloud. I installed the...
Hi,
I'm migrating a project from SDK 14.2 to 15.3 and I wanted to use the generic and "full" sdk_config.h located in config/nrf52840/config/.
The documentation says...
Hi everyone, I would like to confirm if this is a bug.
Per the comment, it seems that the intent of the code is to reject an attempted SoftDevice update.
However, this...
