Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hi
Sorry,This case is the following of case ID: 278538, I didn't find a reply button option in case ID: 278538,So I recreate a new case, I failed to create a new application...
Hi. I am trying to get the gsm modem sample project to work with an nRF 5340 app and a Nimbelink LTE modem, NL-SW-LTE-TC4NAG. The only change I made to the project was to...
Hi Nordic Support Team,
First sorry for basic questions.
I'm learning the basic hardware setup & Linux driver configuration things to setup & configure the MCU(i.mx6)...
Hi, i am Agustin.
I am working with Thingy 91. I am using the Asset Tracker V2 application to upload data to AWS. I have a problem with "Build Solution".
Hi , I got a problem when testing nrf53 qspi signal using a logic analyzer ,with a non-blocking init of qspi and a 4 Byte write , codes are below:
I got a word align problem...
Hi Team,
I want to use the Nrf52840-CAKK-R7 chip to fabricate a PCB board. And communicates with other chips by SPI interfaces.
Now, I want to select the GPIO ports by...
Hi All,
I'm using nRF9160DK PCA10090 Version 0.9.0 and I want to update the Cellular Modem Firmware using nRFConnect 3.8.0 Programmer v2.0.0. Debug Probe is switched to...
We have a timer with a number of variably sized intervals as illustrated below operating on a single capture/compare channel (CC):
Currently the method we use to set the...
Dear all,
In the datasheet and online it is mentioned that the DAP (Debug Access Port) is activated when a programmer is attached. Moreover, it can happen that the programmer...
Hello all,
I am trying the get working the example project nfc_writable_ndef_msg on a nRF52832 with the nRF5 SDK.
I have tried the others NFC examples were most are based...
Hi I am trying to update the connection interval of a peripheral device (nRF52840 ) and I have followed the steps mentioned here .
After Enabling the ble on the device I...
Hi Team,
I have several nrf52840 developing boards for developing BLE Mesh applications.
Now, I want to use SPI interfaces. I didn't find any instructions or examples...
Hi
I am struggling with timer in counter mode. What i need is the counter to calculate time between each loop in microseconds. I do not want time interrupts i just need...
I am currently writing code to read the battery voltage using the C language. I would like to include the header file "es_battery_voltage.h" and use the two functions "es_battery_voltage_get...
