Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
There seems to be a blanket statement of v5.1 compliance here:
https://www.nordicsemi.com/Software-and-tools/Software/S140/Download#infotabs
Does this apply to all revisions...
Hello, when will the v8.0.0 version of the SD for the nrf52840 be available? It seems to be listed in the SIG webpage, but not available for download on the nordic webpage...
Hi,
While trying to measure timings with input captures and pin interrupts, I noticed that the SDK-provided pin changed event is very slow : by the time my handler starts...
I am trying to port my working application from a nrf52811/s112 to nrf52832/s132, both with SDK 16.0.0. I'm at the end at the process, it builds fine on nrf52932, I just can...
I'm new to develop firmware on nRF9160-DK, and my first target to add APN to use LTE-M.
For now, I'd like to do a simple way in the below even this is temporary.
=> Hard...
Hello,
I try to transfer the thread_mqtt_sn_client_publisher example from the pca10056 to the pca10059.
Before that, I tried out the example with the pca10056, a boarder...
Hello! me and a coworker are developing a library for communicating with a peripheral via UART. The main idea is that when we send a command, we should get the corresponding...
Hello Team,
I am new to the OTA process for nRF52840. Please help me with the below query.
1) Is it possible to perform the OTA over BLE and over thread network as well...
Hi, We use the QSPI already very well for a flash device that has the correct commands. Now we want to use a SRAM, also QSPI prepared, but it has some other commands, there...
I'm trying to decide on a protocol to use between two nRF52840s.
Both will connect to an App and each other at the same time
Latency is important because the communication...
Hello everyone,
I'm currently trying to get a SiLabs WF200 WIFI module working with a nRF9160 as the host running on Zephyr. Unfortunately I do not get any clock signal...
Hi,
I am testing the advertisement packet scanner based from nRF5_SDK_17.0.2_d674dde\examples\ble_central\ble_app_uart_c.
At current stage, I can receive the advertisement...
I want to use bootloader for nRF52811.
On nRF5 SDK 17,
exmaples/dfu/secure_bootloader/pca10056e_s112_ble/config/sdk_config.h #define NRF_DFU_APP_DATA_AREA_SIZE 8192
...
I am writing a basic health device application, It starts, loads saved data, starts advertising, takes measurements, if a connection occurs the data is transferred, other...
