SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
I have written two functions to write and read data from the flash using flash_fds module. In this way I am calling the function to write the data to flash :
fds_write_record...
Hi there,
I was comparing the power consumption of ble_app_hrs_freertos and ble_app_hrs examples on nRF52840 DK. The average VDD current is 7.4 mA for the example running...
Hello,
I'm in need of turning on and off the LTE link to use the GPS in cases where I can't depend on PSM. The LTE Link Controller library is good for this however I have...
I'm in trouble... My design has 3 SPI devices, and at a late stage I ran out of GPIO so I added a I2C I/O expander before spinning and building my PCB without thinking too...
I'm trying to use nRF sniffer 3 and can't get it to detect the dev kit on Windows or mac. I've installed it into wireshark and see the toolbar, but no interfaces are listed...
Hi,
Can we give a voltage more than VDD+0.3V on an open drain high impedance configured IO pin? By open drain, I mean:
nrf_gpio_cfg(pin_num, NRF_GPIO_PIN_DIR_OUTPUT, NRF_GPIO_PIN_INPUT_DISCONNECT...
Hello, I am trying to follow and understand the MCUboot encrypted image design found here: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/mcuboot/encrypted_images...
We are trying to connect to discovered smartphones with a Nordic 52840 chip, with S140 softdevice, discover the gatt table, read and write attributes. Most of the time it...
Hello,
I am pretty new the BLE development stuff and was mostly working on an application that works with an existing connection. But because my colleagues are not able...
I am using nrf52832 ble, I want to set the pin P0.2 low as analog input and p0.3 high as analog input .
#define AIN0 2 // analog pin p0.2
#define AIN1 3
#define AIN0_PIN_CONFIG_HIGH...
SDK: 16
Mesh SDK: 410
Example: Light Lightness Server.
I discovered a bug when using the "Move Level" message that doesn't allow the LED to turn off after the move...
hello sir/ma'am
we are using nrf52840 chip in our customized board product and IAR as a development environment and also a debugger called segger jlink .we are not able...
Hello
we are thinking of using the nrf52832 (sdk 16.0, s132) , which we are a bit familiar with by now.
We have a project in which we need to transmit data to 150 unit...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1. I am using ‘ble_app_blinky’.
I am new to BLE certification. I have few queries on BLE Certification...
